Re-Review: Hazard4 - Escape RG

Escape, as new

As posted in RecoilWeb ..... 

Ages ago I covered an essential piece of my EDC, my custom made EDC holster harness. This faithful piece had been with me for years, and has reached the end of its life. I found the Hazard4 Covert Escape RG combination set, and for the last 18 months, my personal carriage needs have been more than met.

Hazard4 are the "Tactical" arm of Civilian Lab makers of fine modular kit. The link I followed brought me to these, this is the Loader rig with the optional extra anatomic harness.

What it is, is two sets of the Escape Rig, one for each side. The two halves are identical, so I'll cover them as just the single unit.

Here are the two Escape halves, with the Anatomic shoulder harness, and another piece at the bottom to hold them together for stability.

Two pouches, with Anatomical Harness and kidney strap

The pouches are made of Dobby Nylon and have "PU X 2" treatment, and measure 12.5 x18 x4 cm
(~5" x7" x1.5") externally. The main panel is faced with two hook and loop closing pockets, one that fits my Surefire 6PX like a glove, and the other which his more squat.

Both of these pockets are elastic sided, and open cornered. Bear this in mind when looking to fill them. I've had smaller items slip through those gaps, and out of the top, but once I'd found the right fit, I've not had any problems.

Rotating Buckle

In this shot you can see some of the rotating buckles  that are fitted to each corner, each backed with a tab of the same padded material that backs the pouch for wearer comfort.  This is some very thoughtful and innovative design. no more buckle-pinch!

You can also see one of the tri-glide buckles that sit on the middle of each of the four sides. These are for accessory loop and strapping, and I'll get into that a bit later.

The 2013 version of this pouch has all black labeling and non-reflective zippers and fittings, for even lower profile wear.

Front pockets

The "back pocket" of the pouch is an open slot, wide enough for my receipt and card filled wallet, and is mesh-sided to cut weight and improve breathability and drainage. (Luckily Australian money is plastic, in case I ever take a dunk...) You can see another of those elastic-looped tri-glides here, to which I have dummy-corded my wallet. No more dropping it into the toilet, off piers, or leaving it on cafe counters for me!

My iPhone sits in the corresponding other side.

What you cant see is the wide swathe of black loop field, for affixing a hook-backed holster, like the Stick-Up.

You can also see the double zipper here of the inner pocket. Very useful!

Inside the Shuttle

Inside that inner pocket, you see where some real thought has gone into making these pouches. As well as the tough nylon outer, they are lined with quilted micro-suede

They also feature a series of webbing and elastic channels to fit your tools and needful gear, I have my SAR Dead Ringer comb and CRKT K.I.S.S. folder in mine on this side. Passports, and paperwork on the other side.

The pocket opens all the way to the bottom, but, like a good admin pouch, it has webbing retainers, keeping it from flopping flat, but catching it at about 45o so your pens, USB sticks, or whatever don't tumble off into the wide blue yonder.

The back pocket has a press stud on webbing closure, with two sizing options, which is great. I tend to clip my wallet in with the big, and my phone in with the snugger length.



The back of the pouch features a belt loop,wide enough for all the belt I tried it on ( both my 5-11 TDU belts, the 215Gear Ultimate Riggers belt, and the PM Leather Hobble Belt.

Left and right pouches, after 18 months

It also features a press-stud flap option, for quick-release needs.

Why even have a belt loop? Modularity! One of the coolest things about this whole system is that it can be worn so many ways.

 Those corner buckles attach to the included cross-straps, which are two fully adjustable nylon webbing straps, with a press-stud in the middle, to connect the two. All of the straps will "double-back" through the buckles for a really secure fit.

Left and right pouches, after 18 months, side by side

 The tri-glide attachment points allow you to rig any number of stability or alternative attachment options. The rotating corner clasps mean that the straps stay flat no matter what configuration you wear them in, and they stay upright as you move, depending on how you wear it.


The included cross-straps are a little more versatile than the Anatomic straps, but not nearly as comfortable. The pouches can be worn under the arms, holster style, singly or in pairs, horizontally or vertically, but also on the hips on a sling, as a backpack, slung cross-ways like a bandoleer, on the thigh as a drop-leg or on the front of the chest or even as a shoulder bag.

Left and right pouches, after 18 months, trimmed and untrimmed

I used one of the cross-straps to act as a kidney-height stabiliser,  having found that on their own, the pouches slid forwards when I bent over without them.

 One last thing. Each of the pouches comes with a "Shuttle Pouch" which is made from the same Dobby Nylon, and lined again in the quilted micro-suede with mesh pockets along with nylon strapping. The Shuttle pouch is designed to fit into the "Back pocket" of the main pouch,and be clipped in. It features waterproof zippers and a set of webbing eyelets on each of the four back corners for dummy-cording (mmm, dummy-cord: looks silly, keeps your gear on you...).

Single pouch, ventral style

This was a seriously feature and function filled set of kit.

I've been wearing it now for 18 months, every day, getting the configuration and fit right and I must say, it has been one of my better EDC investments for some time. 

I don't feel "dressed" with out it, and it really is my go-to item when it's time to run out the door; be it emergency, fire, flood or groceries.

That said, 18 months worth of wear have taken their toll. The Dobby Nylon has pulled from its seams along the long edges on both sides, in once case, Ive needed to trip the front set of pockets right off, because of them flapping about. 

Side wear, no jacket

Side-draw, under jacket

Under jacket, back view

Under jacket, front view

I wear it every day, all day. I tent to wear a waistcoat when its warm, or a jacket if its cold, when I'm going to be at work, or around people I don't want to give the impression that I'm packing a pistol, because it often gets that kind of question. Depending on your situation, you might want to bear that in mind.

I've traveled internationally with it, and keep my passport safe and snug in one of the shuttle pouches, both of which I have strapped into the main holder, to keep them from falling, or being lifted out. Again, they raised some eyebrows at the security counter, but they kept all my valuables up above my bet, and against my body, so I was happy.

Review: Hummingbird - Mega hammock

Summer has arrived here in Melbourne ( don't let the rain and storms fool you) and I have broken the hammocks out, because in the afternoon and evenings, our house retains the heat and radiates like an oven.

I've covered hammocks before, with the Eagles Nest single hiking hammock, but I found an excellent Kickstarter for a mega hammock, to suit my burgeoning family needs. The good folks at Hummingbird Hammocks pitched a "Mega Hammock" and successfully funded.

The mega hammock is designed to hold three to five people, and is rated to carry 450kg (1000lbs). I like to sling it in my back yard, and have taken it camping (although we didn't find a good place to set it up, so haven't had the pleasure of sleeping in it, in the wild).  It measures 5.5m x 2.4m (18' x 8) and spreads out nicely.

Three distinct panels are sewn together to form the body of the hammock, and Hummingbird are proud to say that they use construction techniques borrowed from the Parachute Industry Association, and materials that are likewise parachute grade.

Their mega hammock is made out of 1.9oz polyurethane coated ripstop nylon, which is incredibly strong (rated at about 100lbs per square inch.) The edges of the hammock have type 17 nylon webbing sewn in and used for the attachment points to the four corners. This webbing is rated for 1100kg (2500lbs), will not stretch, and is low bulk. The fabric has a lot of give, and the edge seams and the three panel seams are sewn such that you get uniform "give" throughout.

All the stitching is done on an industrial sewing machine using size 69 bonded nylon thread, which along with everything else used to make the hammocks is very strong and is the very same thread used on parachutes.

They offer several different colours, but I jumped at the coyote-brown option, whcih also goes some way to cover up any goopy-hands stains that my minions may present.

In additiontothe webbing loops in the corners, Hummingbird supply soft link attachments instead of traditional carabiners. These are apparently used widely in skydiving today as a means of connecting the parachute lines to the jumper. They contain no hard parts, are stronger than a carabiner of similar size, weigh next to nothing, and are impossible to cross load.

A simple length of high strength cord, with a loop at either end, one end having a tab of webbing sewn in.  You loop it through itself twice, and you have a light, secure and bomb-proof anchor connector. I have lengths of 2" webbing that I use as my attachment to the steel beams, concrete pillars and roofing beams that I sling mine off. I figure the 5500lbs breaking load the webbing means I don't have to worry where I sling this. Perfect for the rafters of an abandoned warehouse, or between Ewok trees.

The hammock comes with its own stuff-sack, and packs down into a small-pillow or sleeping bag sized bundle. It was quite an investment, but thus far, if nothing but the joy of my littles ones is a measure, it's been fully worth it. Having a portable, hardy betting option is nothing to be sniffed at either, and there are many situations where I would want to bunk-down well off ground level.

Especially if I need to watch out for stobor.

The Hummingbird Mega hammock certainly is big, and quite comfortable with a number of people in it. Be sure to sling it high enough to be off the ground when loaded up, but not so high as to be impossible to get in or out comfortably.

Review: Tactical BBQ apron

I've been holding off posting on this one till an appropriate juncture, and I think this day has arrived.

This is the Tactical Chef Apron by ThinkGeek, and I just had to tell you about it today.

I'm all for being equipped, and being caught out at the fire-line without the right loadout can mean the difference between slabs of hot steaming, bleeding meat, and charred inedible ruination.  That is when having this kind of kit is essential, if not life-saving.

Made of 100% cotton, you can expect the apron to protect your thorax and groin from all but the worst boiling-oil splashbacks, and flare-ups, and perhaps even the exploding kernels of maize.

Featuring a top section of 6 rows of MOLLE loops, with 6 usable channels in the mid chest, and 10 channels at the rib-line, and a further three rows of 10 at the bottom of the apron, this is a modular combat chef's dream.
Twin sets of triple D-rings, mounted  at the upper regions allow for a variety of hung items, and twin snap-clasps at the the waist line give direct attachment and retention options. Three PALS/MOLLE compatible hook-hand-loop fastening pouches, one triple set and two larger sets, one with a look-filed for ID, unit or morale patches offer a variety of mission specific load-outs.

The lower section of the apron features three dump-pouch pockets, for a variety of accessory and brain-grenade carriage capacity.  Watch out for the pocket stitching cutting through MOLLE loops though.

The wide shoulder straps are not adjustable, but come "hero-sized". Fastex style clasps secure front and back, with webbing sliders expanding to allow for the more substantially proportioned combat-chefs.

The back features even more MOLLE loops as well as a broad loop-field for further ID and insignia.

 

Click the picture to be taken to ThinkGeek to buy one!

This is a fun piece, which I enjoy throwing on whenever I face flames, steaming flesh and the wailing of mouths, screaming for blood.

Review: Mudlarks - All-In-One

I took the family up to the snow recently (yes, there is snow in Australia, not very much, and not very long, but it we do get it) at Mount Baw Baw, and in my planning to do so, I wanted to ensure they would be adequately protected from the environment. I posted about what I wore, here)

Triceratops Girl (in pink) has previously been a model for the Muddlarks "Bib'n'Braces"  so I was prepared to make an investment in a set of their all-in-one coveralls for her and Tactical baby. Cold, wet and miserable children are NEVER a good thing, especially in hazardous and adverse conditions.

The whole Muddlarks range is constructed from waterproofed  breathable polyurethane coated, 150gsm nylon rated to 6000mm+. (See this guide to understand what this rating means)  . The fabric has also been Teflon® proofed on the outer facing of the material which helps resist staining and acts as a Durable Water Repellent (DWR). Water, snow and slush just beads and rolls off.

One of the important aspects of staying warm and dry in the snow is not to become wet in the first place, so this is a great material, especially as it retains its breathability. This ensures that the wearer doesn't steam too much on the -inside- which could lead to dampness and chilling.  The all-in-one Muddlarks provide a single piece coverall that ensures no "puddles and snow down the back" moments, with its ankles to crown coverage.

 Moving from outside to in , just unzipping improved their comfort considerably, especially with the polar-fleece lined larger version. This was child-sized hardshell wear at its best, i think.

The attached hood has an elasticised bill, to keep it snugly fitted in high winds, with a press-stud closure at the neck to keep the wide plastic zipper from sliding open. In the "Size 2" option, there are some press-studs at the nape of the neck to adjust the fit for smaller heads.

The hood, and shoulder/back have reflective piping, to assist in locating and safety in low-light situations. 

The back of the suits also feature elastic gathers, to ensure a better fit, with all the seams being taped for additional waterproofing. This was so effective that when Triceratops Girl fell backwards into a calf deep puddle (for her) that she was still bone dry inside even after sitting in it till i could haul her out.

With elasticised ankle and wrist cuffs, the biggest concern I had was that the girls would get snow and slush into their gumboots, but the Muddlarks design had catered for that as well. The fleece lining in the larger size ensured a warm Triceratops Girl, whilst we bundled Tactical Baby with a insulating mid-layer, and she fared just as well.

 Tapered and fitted cuffs, along with the elastic produced a snug fit, without constricting. but it is the button-closed adjustable elastic loop that really makes these a winner. Able to stretch around the ankle of a gumboot then affix, gater-style under them. This combination really ensures a good seal against incidental soaking, especially for little people. Again, cold, wet, miserable little people are not just a burden in an outdoors adventure,but in a survival situation, it becomes an even more serious risk.

I was really pleased with how these performed in the snow, but I've also seen how well the other items in the range (the bib'n'braces, specifically) perform in the mud, sand and forest floor. I really liked these for my kids.

Review: ITS / Zulu Nylon Gear skeletonised bottle carrier

One of my Giftmas presents has gotten a good workout, and as it turns out, this was another of my wish-lust items that was realised. Ive been using a much loved Platatac FUP to carry my poor battered 1L SIGG for the last few years, and its been a great fit, giving shade and some protection to boot.

However, There was something delightful in the lines and modularity in the ITS / ZuluNylonGear collaborative effort of their
modular skeletonized container sling.

Finally getting my paws on one, I wanted to show you just how modular, and hardy this sling is.

Here you can see it strapped to the front of the helmet carrier of my Bullock Echo daypack, where the FUP had previously sat. Plenty of room to attach it again, should I want a double-bottle setup, and still room for the SAR Global Tool Eclipse signal system tag.

The coyote colour was a nice match to the Platatac Khaki that most of my gear is, and it certainly blends smoothly.

Here is where the magic really is. The 1L Nalgene bottle is a pretty wide load, too wide for my Platatac FUP (although they do have the WUP, expressly designed to fit this bottle) The ITS sling is modular, in that it can be adjusted to fit almost any container. You can see here the interface between the two "arm" straps and the base strap, which is sandwiched and locked into place by the hook-and-loop layers.

The elastic shock-cord bottle retainer loop is initially fed through the top of three channels available, which I've indicated here with zip-ties. I like that I can use these to drop down the loop to retain other containers, be they bottles, can or jars, They also offer attachment options for dummy-cording items to the sling, lids, filters, funnels or cups, if needed.

Lastly, the four channel, one row PALLS/MOLLE attachment at the back is more than adequate to attach, fix and carry a fully laden 1L bottle, both on a pack or by manipulating the channels to act as a belt-loop, on the hip.


As with the Zulu Nylon Gear CAOS admin pouch this is a bang-up piece if kit. Rugged, modular and multifunctional, just the way I like, and just what I hoped it would be. Wish-Lust made reality!

Review: Strike Industries - Simple Plate Carrier

This is a really interesting piece of multifunction kit. Strike Industries, in conjunction with J Tech Gear have come up with a multifunction plate carrier, that doubles as a carry case for a laptop. They did my Sling Catch, and Picatinny vertical sling mount
so I've been keeping an eye on their new developments, and was only too pleased to see this cool piece become available, and to receive one! 

This might seem like an unusual combination, but considering the kinds of products on the market now in the US to attempt to protect kids from the alarmingly frequent mass-shootings at schools, the idea of having every-day items with the potential for containing armour is not new. In Australia, we are lucky to have pretty low rates of weapon related violence, but, being prepared for disaster, even the personal and human initiated kind, is what this blog is about. This is the Simple Plate Carrier, and it is anything but merely "simple"...

I've talked about what I use as a plate-substitute before, when reviewing my Platatac MAC rig, and whilst not ballistic protection,  I have again included Polyethylene cutting boards, shaped to the right size.

These not only give me the rigidity and bulk of plates, but I figure that they would also afford me some stabbing, cutting and blunt force trauma protection. Perhaps not as cool looking as a set of Mad Max tire armour, but far more modular, lighter and functional. I have a 34cm x 24cm (13 1/2" x 9 1/2") board in the front internal pocket here, which closely mirrors the SI Plate that Strike industries offers

The back compartment houses both my 15" MacBook Pro, a spare battery, and my iPad.

The rugged cordura-type nylon material of the case is very well stitched, with reinforced seams and bartacking on all the attachment and stress points, without being heavy, stiff or bulky. The wide webbing of the strapping is fixed at the upper edge with vertical fastex type buckles, and at the bottom edge with horizontal buckles of the same type and more importantly, size. Lastly, and this was a big point of interest for me, the back of the carrier features a sewn in handle, laying flush with the back, to turn the whole thing into a modern buckler if needed ....


I found that the laptop charger didn't fit very neatly in the case (it formed a bulge where the plug sat) but because the front of the carrier has three rows of PALS/MOLLE, including two side-by-side and covered in loop-pile, for patches, ID tabs and the like, I was able to affix one of the black Platatac FUP pouches I have, and give myself some extra storage capacity, with out bulking the carrier up too much, or making it too obviously a piece of MIL-SPEC type kit. There is a second panel on the lid flap for a flag-size patch. Depending on how big and full your carrier gets, there may be a third loop-filed exposed, for even more patch-goodness, here's my AFT's Jungle Recon extolling the love of his job...


And here is how the shield handle works, from behind. The main strap is wide enough to give a good bunched grip, knuckles flat against the back of the pad. Because of my very long forearms, by elbow poked out a little of the back when I stand "en guard", so I gave an alternative hold a shot, with my hanad gripping one shoulder strap, arm looped through the hand-hold and the other strap over my elbow.

Both seemed to feel pretty good, and with advantages and disadvantages according to the style of defense used.

When carrying the unit around, I tended to sling the the shoulder strap such that the entire carrier sat under my arm, rather than behind me.

This meant that I could bring the other strap up and over my opposing shoulder, to drop the carrier into the classic "front pack" configuration.

"Nice Target" you might say, about the patch, well, as Batman and the Punisher have said in their respective comics, "I cant armor my face" (although, these days this isn't as true. )


So here I am striking a pose, Simple Plate Carrier as a shield, with my trusty S&W Tactical Pen as my on-hand "please don't make my use this" incentive.

You can see that my elbow hangs out, but when taking a better "buckler and dagger stance" this would be less of an issue. with a combination of the polyethylene cutting board, the laptop and the material of the carrier itself, this was a substantial and solid barrier to put between my vitals and someone without my best interests at heart. All in a package I can happily carry about day to day.

One of the great things about this carrier's design is that the shoulder straps, being all of the same design, can be swapped from position to position. Instead of a "backpacks/frontpack" style carry, simply by changing the straps from top-to-bottom, to top-to-top and bottom-to-bottom, giving you an "around the neck, around the waist" configuration.

All the straps feature a slide adjustment and an elasticised loop to secure loose ends.

This is the classical "Plate Carrier look" and it's a little more conspicuous, but certainly more secure. Wearing the carrier in "frontpack" style, when leaning forwards, it was occasionally tricky keeping the carrier in place, unless I had another pack on my back pinning the straps in place. Good for backpacking and travel in unusual and possibly insecure places, but not full-time.

For the best performance and security, over-the-neck is the way to go.

I've been looking for a means to carry a laptop about. My CSI folder is awesome, and it carries my iPad about in safety, either inside, or slipped beside it in my Bullock Echo daypack, but the Simple Plate Carrier offers the modularity of a inconspicuous armor carrier for a little urban insurance, as well as a means to carry a laptop, and an iPad around safely and securely.

I felt there wasn't much padding for the bottom edge and sides of the laptop compartment, but that was easily solved after-market with a sheet of closed cell-foam. I really liked the lines, and as always, the multifunctionality of the carrier really appealed to me.

Just be sure to remember that neither the iPad or MacBook's are bulletproof .... not to mention cutting boards .... be safe, be equipped and know the limitations of your gear...