Review: ITW - Tac-Toggle

Continuing on my theme of cordage, I bring you the ITW Tac-Toggle. Toggles being one of the more ancient button options available to us it'as no surprise that the sharp eyes and nimble hands behind ITW have taken it from antler-tip, bone and stick into the realms of ballistic nylon.

So, what is it? A taper ended cylinder, with moulded-in notches and two holes in a recessed channel. All up it's just 1 1/2" (40mm) long and 6mm x 8mm thick. The holes are sized to accommodate paracord, but it's a snug fit and I found that melting a cut end to taper it to facilitate feeding it through. Thinner cord feeds without any issue and can even be pinched and fed through as a loop to fit to a strung line "on the bight".

As a line ending stopper on paracord, it's just a matter of feeding the line through both holes and feeding it back into itself.  This forms a very sturdy lock and uses very little cord, less than a stopper-knot for sure. The looped cord lays in the recess and holds the toggle perpendicular to the cord. 

As a stopper, the perpendicular end-knot only makes a sturdy gripping point between the fingers held in a fist, but also as an anchor. The width of the Toggle makes it very suitable for holding items in place through PALS/MOLLE channels. Feeding it in is as simple as turning the toggle 90 degrees and slipping it down through the channels. It is snag free and quick to deploy and detach whilst simultaneously being a sturdy attachment system without needing to tie paracord into the MOLLE directly.

Another way to feed cord into the two holes not as a stopper but along its length, such that the toggle lays parallel along the line and sits in place allowing the toggle to act as a hitching point for other lengths of cord. Pulling a length of line through the holes gives you loop of cord to hang things off, a series of these would give you a daisy chain of attachment points for all manner of gear. 

Simply having a toggle at the end of a line can also enhance the pull capability of cordage, with an improved grip on a toggle between the fingers over a knot or just bare cord. good for dressing lashings, hauling loads or compressing bundles. 

So, as well as securing things to to PALS/MOLLE  and acting as a tie-off point or tensioner on  guy line, I use one of the toggles to secure my wallet. I run a length of paracord from my  Hazard 4 Loader harness and have previously just used a stopper knot to secure it through a hole in the middle of the bill-fold section. I replaced the stopper knot with a Tac-Toggle and my wallet has neither slipped loose nor become dislodged. It also means I have a spare toggle in my EDC in case I need to work some cordage. It also wouldn't look out of place

All in all for a small piece of kit I'm impressed. It brings form and function, and the simple elegance of an ancient device in a modern format it brings  a lot to the table.

Fit two and you've got anchorage for a bow drill, or grips for hauling a sled up a hill. Fit one to a line and feed through a button hole for an unobtrusive  "deep carry" for a SERE kit like the Oscar Delta SPD . 

Wish-Lust Review: Defence Systems Australia cut resistant clothes

My favourite vendor at the Australian Security Expo was Defence Systems Australia, which probably comes as no surprise.

Defence Systems Australia (DSA) is an importer and retailer of innovative law enforcement and security products from around the world, specifically catering to the law enforcement officer. Rather than the usual tactical type gear that I have come to love, they cover some of the less glamourous end of it all, mostly suspect and prisoner related items, to protect the officers from things like stabbings, biting and less savoury attacks like spitting and the like. That might sound a bit off-topic for a blog lke this untill you consider the old stand-bys of zombies, plagues and civil unrest. Having a less tactical layer that offers significant protection is well worth looking into, which is why DSA caught my eye.

The DSA supplies the personal safety products specifically catered to the Law Enforcement Agencies, Security, Military and State and Federal Government Agencies.

They offer a range of slash and stab resistant clothes, covering a range of sensitive and at-risk areas, such as:

•Our throat, which harbours the carotid artery is certainly among the most at risk locations of our body. A cut through the carotid artery would most likely result in death. Our slash resistant turtle neck jacket or sweatshirt would protect this area.

•The radial artery can be found in our wrists, which often is subject to cuts during self defense or whilst protecting our face.
•The femoral artery is a general term comprising a few large arteries in the thigh. Cutting of the femoral artery would lead to a massive loss of blood within e very short period of time.
•The axillary artery is a large blood vessel to be found under your arm pits.

These clothes are built to the following standards, which meet or exceed ISO, ASTM and EN ratings for cut, and tear resistance:

ISO 13997:1999 Blade Cut Resistance Level 5 22Newtons: Cut Tex® PRO +27.8 Newtons
ASTM F-1790 Blade Cut Resistance Levels 4 1500-3499 grams force: Cut Tex® PRO 2580 grams force
EN 388:2003 Tear Resistance Level4 70+Newtons: Cut Tex® PRO 398.5 Newtons

DSA also offer a range of bite-rated protective overclothes, such as bracer-sleeves and a very clever over-the-shoulder set of sleeves. Well worth a look in if you are faced with, or can expect to be faced with biting hazards.

I'd be very keen to get a set of stab and slash resistant clothes, primarily because I often do some foolish things with long bladed shiny tools, like the Cold Steel Gladius, my very much beloved Zombie-Tools Deuce sword and the extremely useful and effective Boker Tomahook. Anyone who works with and swings big blades, or even small ones, knows there is aways a risk of cutting yourself from a bounce-back.

Those who work in offensive, dangerous environments like prisons, crowd control or event security would do well to have a layer of protection that they can wear as everyday clothing and protect their vitals, whilst still being able to go about their normal duties.

Check Defence Systems Australia out if you are in the market for bladed penetration protection.

They also have a range of body cameras to check out ...

Review: SureFire - Sonic Defender EP4 EarPro

I've covered a bunch of PPE in the past: body armour, rain and weather wear, helmets, goggles and buoyancy gear. What I haven't really covered before is ear protection.

I have always worn earplugs when out at clubs and concerts, sporting events (RollerDerby all the way!) but also for power tool work and for industrial noise. Generally I have worn the squishy foam earbuds, but have resorted to rolled up cloth, wadded paper and even Blu-Tack in order to preserve my hearing in loud environments. Mostly nightclubs.
The problem with all these kind of earbuds is the loss of clarity. Or you go to over-head ear-muffs and lose even more.



When I saw the Sure Fire Sonic Defender EP4 on Platatac's website, I thought I'd take the plunge with something more professional.

These hypoallergenic, medical-grade polymer framed plugs fit into the contours and folds of the ear, in ways that are both comfortable AND secure. No more foam popping out, these suckers stay in place, regardless of how much I am enjoying the PWEI reunion concert I am at, or rattling myself with a hammer-drill fortifying "the bunker". The triple flange design incorporates a patented Hocks Noise Braker® filter, lowering potentially dangerous noise levels above 85dB by upwards of 24dB whilst the little stoppers are in place, but allow for near-normal range of hearing when out.

I also noted that the high and mid-range loss was quite different to that with regular foam plugs, there was much more clarity in human speech, without the sharp high-end sting that naked-earways might expect, around loud sources. Removable lanyard lets you pull them out have them draped around your neck, or gear and not drop them in the muck, should you need to.

The soft, durable, and long-lasting plugs were comfortable wearing for hours, and I was able to answer a call on my phone with no problems. Being a low-profile design that allows you to keep them in place while wearing a mask, helmet, hat, headphones, or supplemental ear muff means you can wear them without being caught with unprotected hearing for those unexpected noises in non permissive environments ....