Review: Loop Alien cord attachment devices

I just can't get enough of these shiny titanium cord-attachment devices.
I've already shown you the Piranha and Fishbone, both by Fishbones which are both awesome, and I have them on my person almost every day.

Whilst they were underway on Kickstarter, another kind of device came up, and I jumped on that as well. I have neglected to cover them until now, but have been spurred on by progress (and another Kickstarter by the same folks. From Canny Designs, comes the Loop Alien Original (small) and Loop Alien Ultra Fast Attatchment (large)

The original Loop Alien (small) is only 33mm x 22mm x 3mm (1.25" x 0.9" x 0.125") in size, I was surprised at just how small they were, but there is a lot of grunt in a little package. Made of Grade 5 titanium, these weigh only 4g. Canny Designs offer these in 6061-T6 aluminium (2.6g) , and 316L stainless steel. Three different metals to suit your different needs and budgets.

The smallest hole of the two "eyestalks" will -just- take paracord, if the end is finished to a point, but bear in mind the stresses this tight fit will put on the cord. Canny Designs recommends 1.75mm Dyneema (400lbs test) cord. Great stuff.

The NEW large LoopAlien UFA is 49mm x 32mm x 5.2mm (1.93" x 1.26" x 0.1875") in size and weighs 16g. It is about 1.5x larger in length and width and twice as thick as the small version. It's paracord friendly too!


The main difference in the UFA versions are the hole cut in the "body" of the device. This means that cord need not be threaded through the hole in the "body" as in the originals, but can rather be slipped through the gap, and over either of the "eyestalk".

Here is one of the UFA's, with paracord lashed through its large eyestalk, and looped through the body as a tensioned slider. Through the little eye, I had fed one of the lengths of 7/64 (2.5mm) silver Amsteel rope through the small eye, giving you an indication of the dynamics you can achieve with these little guys.

There are lots of ways you can fit the cords, either with knots, or self-knitting, in the same styles as those seen on the Fishbones. These however, lend themselves to doing guy-wire securing, and adjustable tensioning of loads of up to 45kg (100lbs).
Here's the small Original, also lashed with paracord, the slant of the eyestalks snags the cord nicely, securing the loop neatly, and with enough room to allow it to slide without rubbing on the opposing line.

I have not used the small Originals as much as I might have liked, not being fully paracord friendly limited my imagination a little, but I have been thinking of using them with shock-cord, to rig things to my kayak.

The larger ones the newer UFA's, which I got through Kickstarter as "super fast early delivery" are likely to go in my car with a spool of paracord, for emergency lashing options

These are very cool pieces of kit, and well worth a look in, especially if you are looking to replace your existing tensioning devices for camping or rigging.

I have been wondering if I could set up shade cloth over the whole of my backyard, (which is concreted over, and radiated heat like no ones business) to help with this summers heatwave.

These might just do the trick in adjusting the sails, to stand up to the hot winds.

Check these out, they are elegant and beautifully designed, as well as being very for for purpose.

Here's just a comparison with the two kinds of Loop Alien, and the two kinds of Fishbones

Lastly, to reiterate the manufacturers warnings:

*** The LoopAlien(TM) and LoopAlien UFA are not designed to support human weight. They must not be used as life saving devices, fall protection or in any manner where failure could cause property damage, injury or loss of life. ***

Posted with Blogsy

Review: Fishbones - Piranha

Yes, here I am again with another Kickstarter project. I'm actually reporting this one out-of-sequence, as through some kind of fulfillment time warp, this is the second of two projects that Brent and Eldrick Garcia put forwards. The first being their very cute "Fishbones" but I haven't had a chance to properly review those just yet.

These are the "v 2.0" product, the Piranha "Knotless gear tie"

As you might have noticed, I am rather enamored of paracord and so should you be! It's great stuff, but one of its great advantages can also be a disadvantage. It holds great knots! Sometimes trying to pick apart a tightly cinched knot can be very arduous, and Brent and Garcia came up with a very elegant solution with their Fishbone tools.

The Piranha is the result of a number of design stages, and really offers great utility as well as a great aesthetic.
Cut from 3/16th" thick 304 Stainless Steel the Piranha measures 60mm (2 1/4") from lip to tail, and 28mm (1 1/4") from crest to fin. There is also a titanium option, for the mass-conscious.

It fits nicely into  MOLLE channels, with the dorsal fin hooking neatly over, and being held in place with the tail-fin notch. I found that that tail-fin notch was a snug fit for Type 111paracord, which proved to be very useful in snagging and camming the cord into place.

Speaking of camming, it is worth noting the Fishbones teams own warning about these devices

"Note: Not for climbing or load bearing applications where failure would cause damage or injury."

So, with that in mind, lets have a look at some of the fun things that you can do with them.

The stonewashed edges of the steel are smooth and rounded,  having been sharp cut originally, but that significantly bites into the cord, so the current models are rounded to avoid this.

You might worry that the rounded edges would slip and not hold the loops, as seen above, in a top and bottom view of one of my preferred hitches, but they hold fast.

The two hook gaps are sized to interlock, giving you a solid connection of two ends of cord if you prefer.

Splicing two lines together is also a breeze with the Piranha, simply by winding one through the other, friction will hold  the lines together, even once tension had been released. Again, here are top and bottom views of this splice.

This was a really nice way to link two ends of cord together, without adding a knot that would likely bind and bite, making undoing troublesome.

One of the things I liked about the balance of the took, was that the "tail fin" notch allowed a loop to be fitted snugly, and dangled to make a fish hook. I successfully snagged and hauled my Bullock Echo from one of its D-rings through this method. For extra security,  I could have threaded a leader through the keychain opening, but that hole is too small for paracord, unless you are using the inner cord after gutting it.



 I also found that I could set three lines simply by using the dorsal notches which gave me a no-slide anchor from which I feel would give a very adequate hold for a tent guy rope, or any other three way roping you might need.

The versatility, small size and light weight (well, at just over 25g per unit in the 304 stainless steel) means that this is going to find its way into my EDC in no short time. If nothing else, they feel great in the hand or pocket, and gives me a fidget-focus when I need to keep my hands busy.

The hook gap also doubles as a bottle opener, adding some multi functionality that I really appreciate, as well as the other uses that the guys behind the Piranhas have already stated.

One of the awesome things that they offered is a quick summary of some modifications that you could apply to the Piranhas. I'm going to give a couple of these a try (and I'll get back to you with how they turn out ... )

 I also found that I could wrap the Piranha around an already strung line, given sufficient slack, to give a mid-line attachment option. So many options, such versatility. I'm also going to cover their original Fish Bones and the heavy-duty Snapper so stay tuned!