Review: ITW - Tac-Toggle

Continuing on my theme of cordage, I bring you the ITW Tac-Toggle. Toggles being one of the more ancient button options available to us it'as no surprise that the sharp eyes and nimble hands behind ITW have taken it from antler-tip, bone and stick into the realms of ballistic nylon.

So, what is it? A taper ended cylinder, with moulded-in notches and two holes in a recessed channel. All up it's just 1 1/2" (40mm) long and 6mm x 8mm thick. The holes are sized to accommodate paracord, but it's a snug fit and I found that melting a cut end to taper it to facilitate feeding it through. Thinner cord feeds without any issue and can even be pinched and fed through as a loop to fit to a strung line "on the bight".

As a line ending stopper on paracord, it's just a matter of feeding the line through both holes and feeding it back into itself.  This forms a very sturdy lock and uses very little cord, less than a stopper-knot for sure. The looped cord lays in the recess and holds the toggle perpendicular to the cord. 

As a stopper, the perpendicular end-knot only makes a sturdy gripping point between the fingers held in a fist, but also as an anchor. The width of the Toggle makes it very suitable for holding items in place through PALS/MOLLE channels. Feeding it in is as simple as turning the toggle 90 degrees and slipping it down through the channels. It is snag free and quick to deploy and detach whilst simultaneously being a sturdy attachment system without needing to tie paracord into the MOLLE directly.

Another way to feed cord into the two holes not as a stopper but along its length, such that the toggle lays parallel along the line and sits in place allowing the toggle to act as a hitching point for other lengths of cord. Pulling a length of line through the holes gives you loop of cord to hang things off, a series of these would give you a daisy chain of attachment points for all manner of gear. 

Simply having a toggle at the end of a line can also enhance the pull capability of cordage, with an improved grip on a toggle between the fingers over a knot or just bare cord. good for dressing lashings, hauling loads or compressing bundles. 

So, as well as securing things to to PALS/MOLLE  and acting as a tie-off point or tensioner on  guy line, I use one of the toggles to secure my wallet. I run a length of paracord from my  Hazard 4 Loader harness and have previously just used a stopper knot to secure it through a hole in the middle of the bill-fold section. I replaced the stopper knot with a Tac-Toggle and my wallet has neither slipped loose nor become dislodged. It also means I have a spare toggle in my EDC in case I need to work some cordage. It also wouldn't look out of place

All in all for a small piece of kit I'm impressed. It brings form and function, and the simple elegance of an ancient device in a modern format it brings  a lot to the table.

Fit two and you've got anchorage for a bow drill, or grips for hauling a sled up a hill. Fit one to a line and feed through a button hole for an unobtrusive  "deep carry" for a SERE kit like the Oscar Delta SPD . 

Review: SORD - Specialist Insertion Platform

In my growing collection of SORD Australia product, which includes their 870 scabbard, the covert tactical hoodie and the finger-warming StormTrooper tactical muff, I also have been making good use of their low profile chest rig, for those times where I just want a couple of things on me, in cases where I'm either going to be moving fast and light, like running and scouting, or having to get into hard to reach places, like caving, climbing or tree-work, but I still want to have one or two needfuls on my person.


The SIP (Specialist Insertion Platform) is a light weight, low profile chest rig designed to fit under or with insertion equipment, be it under a reserve parachute, swimmer scout valise or worn as a standalone rig for TAG drivers or reconnaissance teams.

Weighing in at only 360g (12.6oz) it utilises 330D Cordura construction for minimal weight with full MultiCam tape webbing and ITW hardware at multiple points. 

Through some clever design, you have complete side release at the waist in one buckle for fast transition between the SIP to an Assault rig worn underneath, or just to strip it away entirely as needed. Additional buckles at the collarbone and for the kidney stability strap give you options for adjustments and adds to the don and doff design. 

This makes it quick and simple to get in and out of as you transition between mission phases, as the situation requires. 

The SIP is faced with three rows of four channel PALS/MOLLE, with a single horizontal column of three loos, giving you a single column of sideways attachment. Perfect for a cyclume stick, or a single stack pouch. 

At the top of the vertical PALS/MOLLE , a sleeve pocket, fixed with hook-and-loop closure allows access to a small area, big enough to fit a HAPO NAV BOARD or even a compact pistol holster, I have fitted mine with a map and compass, ID and the like. The inside of this sleeve is also lined with a strip of  loop-file, to ensure that whatever you can fix, is fixed, especially important for holsters, obviously. I would have liked to see a cord-loop in there, for dummy-cording, as I have in my Hill People Gear Runners Rig but I could always add this myself. 

The bottom of the SIP also features a standard hook-and-loop sandwich, which hinges up between the second and third rows for attaching dump pouches, the SORD StormTrooper or other pouches with sandwich fittings, such as the Platatac gasmask pouch.

The shoulder straps can be configured in both X or H style with removable cross bar to give you adjustment and wearing options.

Elastic cable retention on the shoulder straps offers even more stability, giving you a very stable, snug and secure platform to run those few needful items that you've loaded it with. I've done a couple of cross country jaunts with it, along with the StormTrooper, and a dump pouch, and had no troubles with it either chafing or bouncing. I was happy with the fit and the quick release, when it came time to dump it.

The MultiCam is spot on, (unlike that used in the Headsox I'm wearing here) and the fit to purpose is great. It is usually less carriage than I would want, but for those times where I want to run light, it's superb.

Review: Platatac Bongo modular battle belt

It's been a while since I've covered a belt, and I picked up this piece recently, and gave it a good workout over the weekend, so wanted to tell you about it.

I've covered a number of belts before, from the surreptitiously tricky PM Leather Hobble Belt, to the hardworking 215 Gear Ultimate Rigger Belt, and the airport friendly 5.11 TDU belts as well as the very capable Young Guns Battle Belt by Platatac, so I wanted to show you this platform as well. This is the Bongo Modular padded belt (Mk2)


With 22 rows of PALS/MOLLE looping, 18 of which are 3 row, with the two channels beside the buckle being only double channel sets. This gives both a lot of real-estate to work with, but also narrows the form around the front, giving the wearer unrestricted motion when sitting, squatting or kneeling.

Designed to be ALICE compatible the belt includes 8 loops for direct attachment to harness or other vest system, such as my MAC armour carrier or the First Spear OAGRE.


It also sports 4 D-ring lash loops along the bottom, which could well be used for leg-straps too, if that's the way your mind works. The principle buckle is a large ITW buckle, as features on many of Platatac's gear. Twin webbing sliders allows you to adjust the belt from either side.

For my skinny (size 32) waist, I needed to cinch it all the way in on both sides, even when wearing it over belted pants and tucked in shirt. The up side of this is that if you have layered clothes, you will have no problem fitting it as an outer-wear layer.

I wore this out to an event, where is was doing First-Aid type monitoring, so fitted it out with my Half Med pack, a set of twin 40mm grenade pouches (they work really well as disposable glove/ mask storage, for quick access). I also fitted one of my SR25 pouches to hold my wallet, a Blackhawk removable side-plate carrier as a mini-dump-pouch, FUP pouch holding my Fenix TK-51 light, and also the SORD 870 Back sleeve, which I'm sneak previewing here. I didn't run it with a sword in it for the event I was at, actually had it filled with big cable-ties, but that's how I would like to roll... A set of CountyComm Premium EMT safety shears rounded it off.

Thankfully none of this kit was needed at the event, but the belt served me really well. The padding is mesh lined, giving it great weight bearing, as well as moisture management capacity.


I wore this rig just on my hips, no strapping, or braces, for 6 hours or so, including some running up and down stairs, with zero dramas. I would wear almost all the pouches identically, other then perhaps moving the 870 pouch to sit higher, if it was bearing more load, just to take advantage of the PALS/MOLLE attachments, but all in all, I was really happy with the belt. The webbing used for the buckles is sewn right into the body of the belt, wrapping the whole way around, and sits under the top. This made feeding the attaching straps of the pouches, both the Platatac-type integrated straps, and the Blackhawk STRIKE Speed Clips I use, a little tricky, but once in, they were rock solid. The overlap of the belt webbing and the middle row of channels makes it LOOK like its a staggered set of loops, but it isn't. Still, this adds to the stability and security of the belt! I might consider swapping out the ITW buckle for a Austrail Cobra buckle at some stage for climb-rating security, but otherwise this is an awesome addition to my load-out options.

Here's some obligatory tacticool shots of my load-out.

Review: ITW GrimLOC

 When you start to collect a lot of gear, gadgets and kit, the question of "how do i get this to stay on, when I stow it, but come off when I want to use it?" comes up. I've used carabiners for years and years, to attach my keys, wallet and the like to me, mostly using the lightweight accessory carabiners you find hanging by cash-registers. Occasionally I have purchased proper climbing-rated ones, for when I've either been climbing, or wanted to carry some serious gear.

The natural progression for me is to see what others are using, which lead me to these: Apparently originally designed to allow Marines to add hydration systems to their webbing, this is the ITW Grimloc, and they offer a lightweight alternative to metal carabiners for gear storage and utility.

The high strength polymer provides a corrosion resistant, solar heating thermally resistant and lightweight alternative to steel or even aluminium carabiners, for non-load rated tasks. I've read that the breaking rating on the GrimLOC is 80lbs (36kg) and this is actually a design feature.  It prevents the wearer becoming caught up in slings and gear and trapped in potentially a threatening situation. It is also strong enough to take a fair amount of rough treatment, as a sling connection point to a plate carrier, for instance, without compromising utility.

 The way it works is that the curve of the D is hinged, with a locking end which operates by a push button. This mechanism is spring loaded, and incorporates a very clever Self Purging "SP" ports along the sides of the D to eliminate sand from blocking the mechanism.

These ports, along with the deeply fluted sides of curve of the D also add to the positive grip needed for   wet or gloved hands. This also reduces mass and adds strength.



 The locking mechanism will pop open given sufficient force, but will also open with a simple one handed press on the button, and opens partially, or with a little more force locks into an open position.

I've used this to hook my phone case to, run hydration tubes and comms cables over and round my shoulder straps and even offer a quick spot to dangle a bag.

The real magic of the design however, is the built in PALS/MOLLE loop feature.

That angled slit 1/4 along the length of the bar of the D allows enough of a standard 1" webbing strap to be fed into the gap that it will be able to be slotted in, secured into position, without compromising the strength of the clip, and eliminated the dreaded "carabiner roll" where the gate can migrate away from where you want or need it, usually pinching you in the process.

Here are a couple holding my ZuluNylonGear CAOS Admin Pouch to my Platatac Bullock Echo

When fitted properly, the GrimLOC will sit in place, where you need it, for as long as you need it, and come out without any fuss or tools.

I usually fit mine such that when they open, the gate forms a hook, rather than dropping my gear down to the ground. I suppose if I really wanted to go for the "high-speed/low-drag" alternative, I could flip them around, but really, I'd prefer to keep my gear snagged to me at this stage. I know, such a Geardo ...

These are great clips, come in a variety of colours to math your kit, and fill the gap that el-cheepo accessory carabiners simply can't be trusted  to fill.