Review: EDC Monster Titanium Multi-function Pry Bar

Time for another pry bar! Having just covered the small titanium pry bar I wear in a belt pouch you might be asking why i have yet another one. (on top of the WTF prybar I wear around my neck as EDC). The short answer is Two is one, One is none, and I have two hands and hate being kept out of places. 

This is the EDC Monster Pry-Bar, which was launched via a Kickstarter project. As their sixth successful project ( they make a lot of folding pen-knifes and the like). The thing that caught my eye about this tool however was  its multi-function design. It's packed full of options whilst retaining rugged construction.

Milled from a block of corrosion resistant Gr5 Titanium, the tool features a number of useful features the designers workshopped from common EDC tools.  

First and foremost the pry-bar end of the tool is dual-beveled on the top face and has a bevel on the under side too, finishing up as a 1-2mm flat edge 15mm long rather than a sharp chisel edge. Not sharp by any stretch but plenty pointy enough to cut taped boxes and packages open. 

A good sized bottle opener sits at the belly of the pry end, in front of a finger notch. The double sided beveling allows the tool to be worked-into a gap easier than if it were flat on the underside, which is handy.

 The back spine side of the tool features a swiveling, magnetised cover that turns to reveal two hex bits, a S2 Alloy Steel  Phillip's head and a flat head driver, both held in place with magnets, but easily popped out. both drivers fit the ratcheting driver ring seated in the butt-end of the tool, it ratchets in one direction only, so you flip the tool to change direction of driving.

It's worth noting that the driver bits don't lock into the ratchet driver, and need to be held in place by the user, (placing a thumb on it seemed to work fine, but worth noting) . You could swap out the drivers with others as long as they fit in the recess.

Recessed on the underside of the tool is a magnetically affixed, titanium bodied "everlasting graphite" nibbed pencil. More than just a gimmick, these pencils are very useful for always to hand writing implements, though I have found the nibs to be fragile on occasion, they do write really well and are super handy. Astute readers may have noticed one lanyareded to my other EDC pry-bar

The pencil is short (1.65")  but not unworkable so its a very useful addition and is securely held in its recess, protecting the sometimes brittle nib, when not in use. 

The very butt-end of the tool features a tungsten carbide spike to allow glass breaking and inscribing into hard surfaces. It also features a lanyard hole for fitting you favourite beads or "don't-loose-me" cords. 

As well as the well placed groves milled in for grip, there are four recessed slots (2 on front, and 2 on the back) for fitting tritium vials. But due to shipping restrictions, they were not able to provide the tritium vial, but they did will provide luminous rods as add-on options. I have yet to install these but should be a matter of applyng a dry-clear epoxy glue. The tool has a removable belt clip, but also comes with a snug kydex sheath with a belt clip. All told the tool including its bits and pencil weighs only 85g (3oz) and measures 14.2cm (5.6") x 2cm (0.82") broad. Its a nice compact tool packing a lot of utility into its small frame.

Review: Rhino Ropework - Tritium fob

I wanted to get my partner Lorin a piece of jewelry for her birthday, but didn't feel that a store-bought piece was really "me" ( as you might imagine), but I was lucky in that I'd been following the exploits of Shane Marks of Rhino Ropework who as well as some really excellent looking marlin spikes and fids for ropework, has also been turning out some really lovely fobs, and better yet, hollowing them out and fitting them with vials of tritium!

You may recall that I had a bead made, with six vials of tritium installed by H3, for my keychain,and I really liked it, though that bead had exposed vials, all but two have since been broken.


The fob I commissioned encompassed the vial, with four sets of three holes drilled, allowing the light to be exposed, but protecting the vial in its sheath of stainless steel. I was very pleased to see that its light, being a much bigger vial, was quite bright, and well exposed by the fob. It is certainly bright enough for me to pinpoint it in a darkened room, tent or in fact, deep underground whilst caving on a recent adventure.

The fob has a hole drilled through at the top, with which a necklace, be it link or a ball-chain to suit the wearer, or even feed a thin split ring through to add it to a keychain. The vial is securely seated and snug within the fob.

It's an elegant piece, rugged and functional in the same moment.
Probably the best part about it was how much Lorin enjoys wearing it, and consequently how much I enjoy seeing it being worn. Much like the SAR GlobalTool MoonGlow disk I wear, it is a great spotting device, without being obtrusive. With tritium, it's glow will last for years, no recharging needed.

Rhino Ropeworks  produces tools in copper, stainless steel, brass and even some in titanium. You should totally check out their Facebook for the most recent tools and designs, and watch this space for when my marlin spike comes in!

Review: Hydrogen-3 Workshops - Tritium bead

I know I am late to the playground when it comes to the cutting edge of self-illuminating lights, but I finally laid my paws on some tritium radioluminescence,  in the form of this gorgeous bead from Hydrogen-3 workshops.

For those of you who don't know, tritium (H3) is the ever so slightly radioactive heavy-brother of regular hydrogen, which sheds electrons as it slowly decays, which in turn excite a phosphor coating on the inside of the glass phial is is trapped in, and, tada, a constant (if dim) glow. With a half-life of 12.5 years, this isn't a "forever" light, but it also doesn't irradiate the carrier either ...

Hydrogen-3 Workshops offer a variety of cool ways to carry their range of tritium phials, (which they have with phosphors glowing in Green, Blue, Ice Blue, Pink, Purple, Red, Orange, Yellow, White), and the bead I chose was a six-sided AISI 304 stainless steel, handcrafted from a metal bar stock and milled to accept six 6 x 1.5 mm tritium phials.

The phials themselves are glued into the bead with the rather cool UV-cured Norland 61 Optical Adhesive and are recessed below the lip of the bead, for added protection.

I chose two each of Red, Blue and Green, for a classic CRT effect. Spinning it, I get a nice off-white glow.

 Adding the bead to my keychain was as simple as slipping it over one of my nifty titanium split rings and onto my Gar-A-Biner to go along with all my other cool EDC keychain tools.

As far as how well it illuminates, I've been able to spot my keys in the dark of my room, the foot-well of my car at night, and at the bottom of my bag, when rummaging at the pool. I'd say the green was the clearest to spot, but the red was not too far behind.

This was a pretty small sized phail for each, so I didn't expect much, but I think they will prove valuable when it comes to finding my keys in the dark of a foreign bedroom, underground lair or ditch when dropped evading zombies.