Review: Zombie Outbreak Hydro Bugout pack

Following on from my Zombie Outbreak Grunt Plate Carrier review, is another item in this line, again, thanks to Global Gear for sending them my way. This time I'll be showing you a daypack. This is the Hydro Bugout Backpack and here is what I can tell you about it:

Styled closely to that of the Maxpedition Typhoon or the Maxpedition Malaga from their Gearslinger range"

This is a smallish pack, measuring in at 30"W x46"H x 5"D with a storage capacity of 25L and happens to be loaded with features. One of the first things you notice about this pack is that it has some serious compression strap options. The front strap arcs over the top of the pack via two straps forming a v-shaped yoke over the front top external pouch, then connects to a webing strap that runs the whole length of the pack, with a Fastex style clip closing the two ends, and a D-ring pull toggle to assist in compression. The v-straps have sliders to adjust their tension as well.



The backside of the pack shows off the adjustable, and removable shoulder straps, a feature I really like, as it gives a whole new dimension to modularity and storage, carriage and orientation of the pack. At the top side of the straps, two close d-rings give a friction-feed closure to the shoulder straps, via the thick and heat-sealed webbing straps, before meeting the closed-cell padding of the harness. The front side of the shoulder straps feature more webbing, with PALS/MOLLE loops here and there, and more d-rings for attachment options. A light sternum strap, again removable, and can be relocated to best suit your needs.

The bottom of the shoulder straps is a more traditional tri-slide type buckle, but is seated on reinforced triangular flaps, giving a nice secure mount to the back, without pinching or pulling the pack. A wide belt with adjustable and removable straps finished off the mounting options. It's also good to note that the back is of a breathable mesh. The last notable feature of the back is the hydration bladder pocket, with a broad hook-and-loop closure and an internal webbing loop to hook a bladder to. I have had trouble fitting a 3L bladder in it, it simply isn't tall enough.




This is the top, front pocket, which is both surprisingly deep, and compressible, is a double sided zipper closing accessory pocket. The front of the pouch features a loop-field backing which has a single row of five channels of PALS/MOLLE loops. However, because of the stitching, only three of these rows are available. The loop field, being bisected by the MOLLE loop webbing, is only just wide enough to carry a nametape.



The front bottom pocket is even more spacious, holding my 1L Zombie Squad Nalgene bottle with plenty of space to each side, for more accessories. Again, as with the top pocket, it features twin zippers and deep sides, and has the main compression strapping running over the top of it. This poses something of a problem, as it limits the ability to get into the pocket to some extent. The front of the pocket features two of the same strips of PALS/MOLLE as the top pocket, this time backed with webbing bands instead of the loop fields of the top pocket. Two short compression straps mount to the bottom band, and allow you to really bind the pack, cinching it in tight.

This is the first and front of the two big internal compartments. It is a fully unzippable pocket, allowing it to be opened flat, and emptied fully, easily. You can see the utility pocket, with it's twin pen holders, and a single deep utility pocket. This is a good shot of the material used in the bag, it is a heavy, plasticized fabric, quite rugged, and whilst not a Cordura type of finish, it seems to hold up to wear well, and presumably adds some significant waterproofing.

The stitching is also clearly visible, and is of quite reasonable quality. The internal seems are all taped, which is great, as it lends considerable survivability to a pack like this, especially if things are constantly being stuffed in, and hauled out roughly...

Inside the second main compartments , which this time does not quite unzip all the way due to the bottom compression straps riding slightly over the base of the zipper, is deeper than the first compartment, and also has the additional bonus of two large pockets. The first sits against the back of the first compartment, and is made of mesh, and is deep enough to hold my iPad comfortably, and securely. The second is against the back of the pack itself, and is zipper closed, but only runs about a third of the depth of the pack, presumably to not eat into the hydration bladder space.

Here is the whole pack, stuffed full of blankets, books, bottles, clothes, and showing you the V-straps of the top compression straps, as well as the two additional single row, double channel PALS/MOLLE loops that are found on the side of the pack. The top seam also features webbing loops for dummy-cording or running a hydration bladder tube which I always like.

You can also see the drag-strap type of heavy rolled webbing handle at the top of the pack, and perhaps under that you can make out the mysterious elastic webbing square. I had initially thought this was the feed-hole cover for the hydration tube, but there was no slit for that purpose. It is also covering a square of loop-field, again, with no clear purpose that I can discern. A mystery, but not an unpleasant one.

Here is my typical load out, when I was teasing carrying it around. It packed quite nicely, and I was please with not only how each compartment filled out.


Lastly, I'll leave you with this: some might call the ultimate test of a daypack: here the Hydro Bugout is stuffed under my Virgin Australia Airbus 330 seat...

I like this little pack, it is well put together, full of features and carriage options. Certainly a good bug out bag option. I think I will be loading it up and putting it in a easily accessible location for the whole family.

Review: Strike Industries - Simple Plate Carrier

This is a really interesting piece of multifunction kit. Strike Industries, in conjunction with J Tech Gear have come up with a multifunction plate carrier, that doubles as a carry case for a laptop. They did my Sling Catch, and Picatinny vertical sling mount
so I've been keeping an eye on their new developments, and was only too pleased to see this cool piece become available, and to receive one! 

This might seem like an unusual combination, but considering the kinds of products on the market now in the US to attempt to protect kids from the alarmingly frequent mass-shootings at schools, the idea of having every-day items with the potential for containing armour is not new. In Australia, we are lucky to have pretty low rates of weapon related violence, but, being prepared for disaster, even the personal and human initiated kind, is what this blog is about. This is the Simple Plate Carrier, and it is anything but merely "simple"...

I've talked about what I use as a plate-substitute before, when reviewing my Platatac MAC rig, and whilst not ballistic protection,  I have again included Polyethylene cutting boards, shaped to the right size.

These not only give me the rigidity and bulk of plates, but I figure that they would also afford me some stabbing, cutting and blunt force trauma protection. Perhaps not as cool looking as a set of Mad Max tire armour, but far more modular, lighter and functional. I have a 34cm x 24cm (13 1/2" x 9 1/2") board in the front internal pocket here, which closely mirrors the SI Plate that Strike industries offers

The back compartment houses both my 15" MacBook Pro, a spare battery, and my iPad.

The rugged cordura-type nylon material of the case is very well stitched, with reinforced seams and bartacking on all the attachment and stress points, without being heavy, stiff or bulky. The wide webbing of the strapping is fixed at the upper edge with vertical fastex type buckles, and at the bottom edge with horizontal buckles of the same type and more importantly, size. Lastly, and this was a big point of interest for me, the back of the carrier features a sewn in handle, laying flush with the back, to turn the whole thing into a modern buckler if needed ....


I found that the laptop charger didn't fit very neatly in the case (it formed a bulge where the plug sat) but because the front of the carrier has three rows of PALS/MOLLE, including two side-by-side and covered in loop-pile, for patches, ID tabs and the like, I was able to affix one of the black Platatac FUP pouches I have, and give myself some extra storage capacity, with out bulking the carrier up too much, or making it too obviously a piece of MIL-SPEC type kit. There is a second panel on the lid flap for a flag-size patch. Depending on how big and full your carrier gets, there may be a third loop-filed exposed, for even more patch-goodness, here's my AFT's Jungle Recon extolling the love of his job...


And here is how the shield handle works, from behind. The main strap is wide enough to give a good bunched grip, knuckles flat against the back of the pad. Because of my very long forearms, by elbow poked out a little of the back when I stand "en guard", so I gave an alternative hold a shot, with my hanad gripping one shoulder strap, arm looped through the hand-hold and the other strap over my elbow.

Both seemed to feel pretty good, and with advantages and disadvantages according to the style of defense used.

When carrying the unit around, I tended to sling the the shoulder strap such that the entire carrier sat under my arm, rather than behind me.

This meant that I could bring the other strap up and over my opposing shoulder, to drop the carrier into the classic "front pack" configuration.

"Nice Target" you might say, about the patch, well, as Batman and the Punisher have said in their respective comics, "I cant armor my face" (although, these days this isn't as true. )


So here I am striking a pose, Simple Plate Carrier as a shield, with my trusty S&W Tactical Pen as my on-hand "please don't make my use this" incentive.

You can see that my elbow hangs out, but when taking a better "buckler and dagger stance" this would be less of an issue. with a combination of the polyethylene cutting board, the laptop and the material of the carrier itself, this was a substantial and solid barrier to put between my vitals and someone without my best interests at heart. All in a package I can happily carry about day to day.

One of the great things about this carrier's design is that the shoulder straps, being all of the same design, can be swapped from position to position. Instead of a "backpacks/frontpack" style carry, simply by changing the straps from top-to-bottom, to top-to-top and bottom-to-bottom, giving you an "around the neck, around the waist" configuration.

All the straps feature a slide adjustment and an elasticised loop to secure loose ends.

This is the classical "Plate Carrier look" and it's a little more conspicuous, but certainly more secure. Wearing the carrier in "frontpack" style, when leaning forwards, it was occasionally tricky keeping the carrier in place, unless I had another pack on my back pinning the straps in place. Good for backpacking and travel in unusual and possibly insecure places, but not full-time.

For the best performance and security, over-the-neck is the way to go.

I've been looking for a means to carry a laptop about. My CSI folder is awesome, and it carries my iPad about in safety, either inside, or slipped beside it in my Bullock Echo daypack, but the Simple Plate Carrier offers the modularity of a inconspicuous armor carrier for a little urban insurance, as well as a means to carry a laptop, and an iPad around safely and securely.

I felt there wasn't much padding for the bottom edge and sides of the laptop compartment, but that was easily solved after-market with a sheet of closed cell-foam. I really liked the lines, and as always, the multifunctionality of the carrier really appealed to me.

Just be sure to remember that neither the iPad or MacBook's are bulletproof .... not to mention cutting boards .... be safe, be equipped and know the limitations of your gear...

Review: Platatac - MAC Mesh Back Pack

This unusual piece is a now discontinued line from Platatac, something of an experiment of theirs that didn't pan out commercially as well as hoped. I however, think they are a great idea. The concept is that a daypack has been mated with the Medium Armour Carrier back-piece.

You'll remember from recent posts that I got this particular piece of gear as part of a deal along with the Front Opening Panel which I reviewed not too long ago, but this is interchangeable with that as well as the closed front MAC plate carrier that makes up the front of my usual rig.

The ability to chop and change these pieces gives the wearer the ability to have a permanently mounted pack, integral ballistic plating carriage and modularity to connect it to an existing front piece.

As with all Platatac's main-line gear, I chose khaki, to suit my aesthetic, and is made of the same 1000d Cordura material I've come to expect from their gear.




As well as two spacious "most of the way to the bottom" unzipping side-pocket, each with a set of 3 row, 2 column PALS/MOLLE, but also with a large  "1/3 of the way opening" main compartment. Inside the main compartment there is an elasticized internal pocket, up against the back wall, suitable for a hydration bladder, or soft-storage. At the top of the pack there is a vent, cut and covered to prevent the casual ingress of water and dirt, which would allow a hydration tube and/or cables to exit the pack.

The pack also has a beaver-tail flap, which is fitted with multiple cinch straps, two fastex-style clips, one on each side, and a criss-cross of shock-cord running through D-loops to give additional storage. The beaver-tail will fit most ballistic helmets, I read, but for my purposes, it fits my Pro Tec Classic skate helmet just nicely.  For all my brain-bashing adventure needs!





























The "inside" of the pack shows off its plate-carrying nature, with a heavy hook-and-loop closing pouch, allowing your vitals to have that much needed protection. Below this, you can see here the belt-pouch, where it is possible to run a waist belt, or the strapping needed to secure the bottom of this piece to the bottom of one of the front components of the MAC family.


The inside of the belt-pocket has another patch of hook-and-loop, to secure any strapping you use to prevent it sliding one way or another. You can also see some additional loops and attachment points. These came in very handy when I rigged this pack for solo-wear, by running two meter-long lengths of webbing from the bottom, up to the fastex-style clips at the shoulders. There are also two sets of wide elastic cable/tube keepers sewn into the shoulders, and additional d-rings for further attachment options.

Underneath the beaver-tail helmet carrier, there is extensive PALS/MOLLE real-estate, with 6 rows of 7 channels, the top one being hook-and-loop loop field, with an additional band of MOLLE-spaced loop-field below that for unit, name or morale patches.

The pack was just big enough to fit my ubiquitous CSI folder and most of my daily needs. I also fitted my bottle-carrying FUP pouch, and my half-med pouch, as well as some other needfuls, as you can see here.

All in all this is a very interesting hybrid. I would have made some further adjustments and recommendations if Platatac were looking to continue the lin, namely to the placement of some of the loops and attachment options, but all in all, it was a worthy investment. Now i can kit out another member of my household, and put a pack on them that cant be lost or forgotten!

Good thinking, and staying prepared!












8

Review: Platatac SCAR Mini Chest Rig

It's been a while since I've covered any purpose made tactical gear, having spent quite a few posts going over the pretty awesome set of birthday knives I received (1, 2, 3, 4, 5, 6) so I wanted to get back into it with some really functional and multifaceted kit, such as seen with this, the SCAR mini Chest Rig, by Platatac. I took a departure from my usual khaki colour scheme, mostly to allow an option of distinguishing one set of kit for another when romping around doing Stargate LRP.

Unlike my full MAC rig, which I'd reviewed a while back, which offers front and back, side to side and sternum to belly coverage, with all the bells and whistles, the SCAR mini rig is a substantially cut back, being in principle a front piece, with shoulder and waist straps to keep it on. However there are still a number of features that Platatac have added to make it more than either just a plate carrier, or mag-rig.

The bottom half is made up of s set of four integral shingle pouches, each with a drainage grommet and featuring a three row, ten channel PALS/MOLLE field. Each of the shingles is closed by a loop of shock cord which feeds through the top row of MOLLE loops for each pouch, and back rough additional row of MOLLE loops above e shingles, Wu a reinforced tab of webbing for each shingle to act as a draw-toggle. Each shingle is reported as being able to carry 2x M4 magazines, or a single Styre magazine.

As well as the thorax belt of shingles, above is the SCAR rig features a sternum piece which offers a further three rows of six channels of PALS/MOLLE attachment goodness, although the heavy fastex type chest buckles do cut into the available space a little, and would make for a very snug fit if a pouch was fitted adjacent to them. This sternum panel is interesting in that it is not permanently attached to the chest straps, but rather feature a pair of press-stud loops which attach either through the plastic D-loops or webbing loops on the shoulder pieces. As well as the PALS/MOLLE field, this sternum piece also features a hook-and-loop closing map/document pocket at the top lip.

Looking at the inside surface of the rig, you can see the wicking mesh that lines the otherwise all 1000d cordura construction, but also the back of the shingle/thorax region has a built in pocket, and the sternum region a corresponding wide band of elastic material to accommodate a chest-plate, should that be required for your kind of activity. (as with my full MAC rig, I'll probably cut down a polycarbonate cutting board to fit in mine, for look and feel if not the innate properties of a cutting board). However, and here is where the SCAR rig shows the clever design thoughts put into this range of products, again, if all you need is a magazine platform, and are not going to be wearing a plate, the sternum piece can be unclipped from the shoulder straps, and folded down behind the thorax belt, dropping your profile, and heat retention.



The wide shoulder straps, which feature loops to secure cables or hydration tubes loop around the arms and fasten back around under the arms, and a similarly broad waistband secures the rig with another large fastex style buckle on one side. I found that when jumping about, the shoulder straps tended to slip somewhat, which is a situation I'd rather avoid in a crisis. To avoid this, I took the MacGuiver approach, and swapped out one of the shingle shock-cords and fitted it as a loop behind my shoulders. This might act as a slight delay if I had to shed the rig entirely, rapidly, but I'm not expecting to be sprayed with acid-for-blood xempnomoroh gore any time soon. Returning the now bereft single to normal function was just a matter of looping the cord through two sets of MOLLE, and as I also dnt expect to be dealing with extra tall magazines any time soon, not having at extra slack isn't much of a worry to me.

This is a pretty cool rig, a lightweight, low-profile platform, which I intend to use to supplement my available loadout options depending on the situation I find myself needing to respond to. Adapt, innovate overcome.

Review: Drop Leg Holster

A while back I attended a comic convention, Armageddon at which there were a number of stalls selling a variety of costume pieces, including a bunch of military looking kit. There was a considerable military cos-play contingent, so it was a good opportunity for me to see how other people wore their costume. Almost all of the costume pieces I saw were just that, poorly put-together costume pieces with bad stitching, un-taped seams, cheep light nylon and flimsy plastic hardware.  I did find one piece that I wanted to add to my collection: This no-name drop leg holster. The material is a stiff quilted nylon, in woodland, my most populous kind of cam. It is a highly adjustable "universal" holster, and to keep the "I don't own any firearms" tradition going, I have it holding one of my Nerf Scout pistols.

As far as a piece of rig goes, its a pretty standard setup as far as I can tell. It follows the same pattern as my 1/2 Leg rig in that it has a vertical belt strap and two thigh straps. A magazine pouch sits just at the forward facing edge of the holster, with a hook-and-loop closure flap.

In this rig, all the key components are adjustable. The top of the belt strap ends in a broad 50mm hook and loop belt-loop, with a hoop of  elastic webbing to give some shock absorption and give for the wearer. A wide Fastex type buckle about half way down gives a fast-on/fast-off option for those times where you need to shake a leg, so to speak, and a thigh-rig gets in the way. At the bottom of the belt-strap is another adjustable hook and loop closing webbing section, which is fixed to the main body of the holster by a plastic hardware loop, again adjustable by hook-and-loop.

Two thigh straps are sewn-in to the back of the holster directly, and following the same pattern as the belt-strap, and features an elastic webbing section, at the body of the holster, with a Fastex style clip. The webbing strap is adjustable with a plastic slide. I found, even with my fairly slim thighs, this was a tight fit. Someone with larger thighs would have considerable trouble wearing this particular model.




The holster section itself is also highly adjustable: Internally there are two strips of hook-and loop, one of which makes up one half of the closure system, the other is positioned such that the loose webbing strip (somewhat obscured by my fingers here) can be affixed to it to cradle the barrel of the holstered pistol. At the top of the holster you can see the webbing tabs with a press stud, for securing the carried pistol. Mine is faulty, and will not "snap" closed. Sign of the low-quality knock-off that this piece is. It also seemed a little "small" and may not accommodate a real pistol, or at least not one with a lighting system.

The holster closes with a three-piece hook-and-loop seam, in which a middle layer (the left side) loops around to the right, and is covered by the long strip of hook-and-loop held out in this picture. This gives a very secure and form-fitting carriage, and the holster is complete.

From this position you can also see that the security-snaps are also adjustable.

All in all, I was happy with this addition to my collection, for what it cost me and what I will be using it for, I will get my money's worth. I would not recommend it however for someone who was going to stake their life on their equipment however. It may well have been made off a good pattern and I like the functionality, the ability to widely adjust its layout and "fit", but this is a theatrical quality piece at best. 

Review: Platatac Bullock Echo daypack

So as I've covered recently, I've been searching for a day-pack to replace my long-time love, the Crumpler messenger bag. Not because there is anything wrong with the Messenger bag, far from it, it's a workhorse, and therein lies the problem. I loaded it up like a horse. I needed to down-size and reduce my tendency to take everything with me, everywhere, like something out of Labyrinth. I think that I have settled on something that suits my needs, and certainly fits my "tough, modular, multi-functional" aesthetic. Chatting with the guys at Platatac gave me the opportunity to get an idea of both my requirements and the possibilities. My primary requirement was one of carriage, but was not a capacity or volume question, but of dimensions. I wanted to be able to pack my "slightly bigger than A4" CSI folder into it, whilst not being a monstrous 48hr or even a modest 72hr bag. Don't get me wrong, "right job, right tool" is a maxim I hold in high regard. I just wanted a little bag. I have previously reviewed the Platatac Nomad and the Maxpedition SITKA-s, but here for your edification and appreciation is the Bullock Echo.Not to be confused with the more basic Echo.


The first thing you need to know is that the Echo is not a stand alone "pack" in its own right, in that it lacks it's own shoulder straps. This isn't as much of an issue as you might imagine, as long as you are aware up-front, and the Platatac retail it's will clue you in right away. The reason this isn't a problem is because of the vast array of attachment options built into the pack, and the option of attaching a separate shoulder straps (as seen in the Kilo Med Pack). Looking at the back of the pack, you can see that it has two 5/7 row deep PALS/MOLLE channels spaced to fit onto a 4-channel wide set of webbing. This is what I use, but I'll get to that later. It also features plastic loop-hardware at the top and bottom corners to attach those removable shoulder straps I mentioned earlier. Six plastic D-loops give even further lashing options. The back of the pack is the same Airmesh material to promote cooling and airflow, and you can see the reinforced webbing drag/carry handle at the top of the pack clearly here too.
 
Note the six cinch-straps (two bottom, two top and two towards the top just above the side pouches.

Lets have a look at the front of the pack. The sloped "kidney pocket" at the front of the pack would be perfect for big, wide angled goggles. I keep my battered old first aid kit , and a poncho in mine. A large loop-field gives lots of patch real-estate, and the three sets of elastisied loops are perfect for cyalume sticks. The zipper is shielded by a lip of the material above, a clever afterthought.

Above the "kidney pocket" is a two row, four channel set of PALS/MOLLE webbing, with a nifty small pocket, good for ID, cards, cash and other small, get-to items. This pocket is covered by a close fitting lip of the material above, so is both well shielded from any possible water ingress, but also from prying hands! You get a good view of the para-cord fitted zipper-pulls here, which give not only a good firm grip, but also greatly reduce the metal-on-metal sound that these can otherwise have. I haven;t thought what I might fit to this particular sport, accessory wise, but it's good to have the option, as need arises. This whole panel, above the "kidney pocket" makes a lid for the next level in, the "Fixed Ballistic Helmet Carrier" which I'll get to in a moment. The Fastex clips that jut from the corners of this flap form part of the closure and cinching system for that carrier. When I look at it like this, it looks like the chest piece of a very small plate-carrier, perhaps it would make a good spot for a mascot to ride, keeping an eye on your six...

Next stop is that "Fixed Ballistic Helmet Carrier". As I've mentioned previously, I don't have access to military/LEO-grade arms and armour, but I do have a pretty adventurous life. I recently bought myself a new helmet, a ProTec Classic Skate, which meets my needs of not braining myself whilst doing dumb things. The problem with helmets for bike and skating, at least, is that they can be fragile, which is kind of counter-intuitive, but mostly a Quality Control issue. The guarantee's offered by the manufacturer tend to revolve around the idea of "one-impact-only", I presume the same kind of rules apply for ballistic helmets. I've read similar things about ballistic plates for body-armour, which is why "training plates" are available. SO, having a dedicated pouch for your helmet, rather than slug off the side of you tossed-around pack, is a great idea. Keeps it secure, out of the muck, and lends it a certain amount of padding. This pocket is mesh-sided, presumably to aid in ventilation.


I can tell you, from kendo, pulling a cold, clammy, sweat soaked helmet on the morning-after is never a good thing. The side-cinch clips can also be attached to the top-cinch clips, to stow contents of the helmet-carrier pocket, by putting that "kidney-pocket" MOLLE flap flat, as opposed to upright. Very clever design. Never ones to waste real-estate, the inside of the "helmet-carrier" is lines with 4 rows of 6 channel PALS/MOLLE webbing. You can see that I use mine to stow my camping cutlery and my metal chopsticks. Day to day, this is where I stow my CSI folder, and loose paperwork I "file" and often, the book I'm reading at the time. As well as the mesh-lined pocket, and the webbing, there is also a full sized zippered pocket as well. A second loop-field tops the back-side of the "helmet-carrier" area, which you can see I've migrated my AFT Angry Ranger patch who is part hero/part role model for me, and a Triple Aught Designs Dog&X-bones glowing rubber Ranger Eyes.


Now on to the "main pocket" of the pack. This tall pocket has a zippered closure that runs the length of the domed top of the pack, but not down the sides, giving a mouth-type access to the internal areas. This means two things; items are unlikely to spill out the sides, but you need to dig to get to the bottom if it's full. I'd much rather dig than have my gear either spill out all over, or the zipper failing, and the bag being useless. With a 4/5 closed pocket, this isn't an issue. Inside are two zippered compartments, one over the other, on the front-side face, and an elasticised Internal Bladder Sleeve, which is a great size for an iPad, as it happens.There is a drainage grommet in the bottom of the pack, and the internal stitching is all top-notch. The seams are taped, bartacked and as with all the Platatac packs and pouches, is make up of the same 1000d Cordura. It's probably well worth noting that as well as the elasticised Internal Bladder Sleeve, there is also a hook-and-loop fastening back pocket, which is where I would be putting a hydration bladder in this pack, although it could also be a place to stow items you want kept extra secure and out of sight.

Above both the two hydration pouches are two methods for securing your hydration bladder. A double sided loop of  hook-and-loop, in the "roll to close" format familiar to those of you with laptop power-cords. The second option is a stitched in loop of paracord. As well as these attachment points, there are three eyelets which I have threaded safety-orange paracord through to show the placement. These eyelets emerge from under three of the eleven loops of daisy-chain webbing that is spread over the arch of the main pocket's lip.

This acts both to shield the insides of the pouch from dirt or water ingress, but also gives the user three options for feeding hydration hoses, or cables out of or into the pack. 


At the sides of the pack, are two additional zipperable pouches, each featuring a three row, two channel set of webbing. These pouches are great for all kinds of accessories, I have my needful tools in one, and lights and compass in the other. I put my faithful SIGG bottle FUP pouch on one side, and the Half-Med kit pouch on the other. These twin pouches feature zippers with the similar philosophy of the main pocket: not all the way to the bottom. They won't spill your needfuls if you forget to zip them back up, with a sizable "cup" being left un-zippered at the bottom of each. They also each feature a drainage grommet, for those times when you find yourself taking a fully-laden dunk. You can note at the bottom of this pic, the shoulder strapping fed through the plastic loop.

This is how I mount my Bullock Echo, piggiebacked on my Alpha Hydration pack. This gives me shoulder straps, and whilst not as slim-line as i might have otherwise achieved with just stand-alone removable shoulder-straps, enables me to use my existing kit to build myself a functional day-pack. You can see my CSI folder strapped in, and not going anywhere, and between the top, side and bottom cinch straps (each of which also feature a hook-and-loop retention loop to keep the excess webbing under control). You can see here that I have my two extra pouches affixed, and a cyalume stick at the back. I figure keeping it there gives drivers something to see in their headlights as I cross roads ...

I fed the shoulder straps of the Alpha through the bottom plastic loop of the Bullock Echo, to give it a little bit more cohesion, and so far, its been fairly comfortable.

Best yet, the Bullock Echo holds all my stuff! I down-sized, removed duplicates and the unnecessary, pairing back to just the useful and needful.  Here is my usual load-out, just out of interest:

So, in summary, I'm really happy with the Bullock Echo. It has pretty much solved my day-pack requirements, it has an impressive carriage capacity, modularity and the same ruggedness I've come to expect of Platatac kit. Not having been able to get my hands on a set of those removable shoulder straps is something to look at down the track, and I think I can see the advantage in a set of the zipperable MOLLE panels that enable rapid transfer of one pack (like my MEOP Medic Pouch) to another, either to the Alpha, or onto the back of my MAC Armor Carrier, perhaps.

Review: Platatac Modular Radio Pouch

Here's one of the last Platatac pouches that I have currently, and it's a pretty cool one. As previously mentioned, I got this as part of a bundled pouch deal and have happily had it attached to the cummerbund of my MAC armour carrier  since I got it. This is the Modular Radio Pouch by Platatac. It is designed to take the AN/PRC-148 MBITR (PRC148) Radio but as i don't use that kind of radio, I felt the need to find alternate uses, which I'll get to later on. This pouch features the same heavy 1000D Cordura that the other pouches like the very useful FUP and SR25 pouches which is not only IR treated, hard wearing but sheds dirt and grime very effectively, I've found. This particular pouch is interesting because like the other Platatac shingle pouches, its open top is managed with a shock-cord loop, which in this case, is fixed with a nylon webbing loop attached to a Fastex buckle. 
 
I really like these buckles, far more than hook-and-loop.  One great feature of this pouch is the two side pockets, which will fit accessories such as my Gerber multitool and my trusty and blindingly-bright Surefire 6PX. The sides of these pockets are elastisised, to keep your item snug and secure, and feature a hook-and-loop fixing webbing cover. The double rows of PALS/MOLLE attachment loops give this pouch the same rock-solid attachment to whatever kit you happen to want to mount it to. You can see the shock-cord loop's knot in its grommet at the back, between the MOLLE loops. A drainage grommet is fitted to the base of the main pouch and a webbing-taking loop is fitted to the stiff and reinforced backing of the pouch at the top, for use as an alternate attachment method.



So, as I said earlier I don't use the big MilSpec radios this particular pouch is designed around, but for my Stargate Lasertag LRP and costuming needs I have come up with a couple of options. Here it is holding an old PlayStation light-gun, which it fits quite snugly, when the shock-cord is adjusted. I don't have an actual handgun to test it on, and I'm sure if I did I would use a purpose built holster for it, but this gives some idea of its capability.  I have also used it to carry one of the extra-tall Nerf Extended Clip .

All in all this is another example of a great piece of Platatac gear, adaptable, multi-purposed and rugged.  I'm very glad to have it in my collection, and look forwards to lots of opportunities to load it up and hump it about!