Thursday, June 6, 2013

Review: Laser Genetics - ND-3x50

After my visit to the SHOT Expo, I thought it was time to roll out one of my big lights. 

I had seen these whilst browsing the Canis Latrans Sports website (they do "replica" gear, where my Ops-Core style helmet came from ...) The idea of a laser pumped light sounded really cool, but I had no idea what to expect. I took the plunge and ordered one.

It turned out to be much bigger than i had expected (I did choose the bigger of the three versions available.) Here it is, the Laser Genetics ND3x50 laser designator (or a clone of the same)


The fist thing I need to tell you is that it IS large. The objective lens end is 60mm (2.35”) in diameter, and the barrel, whilst the standard 1" ring size gives the unit a 240mm (9.45”) over all length. It's a big light at 380g (13.5oz). However, it gives BIG results.

Powered by two CR123A batteries, the light has a maximum output of 50mW, which is purported to give a visible light at up to 4.8km (3 miles). It manages this by producing light at 532nm (green), apparently the easiest light for the human eye to see. 

So it's a huge laser pointer, so what?  


Built into the base of the objective end is a Rotary Optical Collimator, which allows you to dial in the focus of the beam, from 50mm to 320mm at 300mm from the end of the objective. That then spreads out to about 2m at 11m (see pics below), or , when dialed in tight, leaves a pretty much 50mm spot for as far as you care to through, up to about 450m (500yrd) effective range.

By "effective range" I think they mean when mounted on top of a scope, which, as it happens, they include mounts for with a "weaver style ring", a 1" scope mount (essentially a windage and elevation adjustable double sided mount, a tripod mount, as well as a pressure switch accessory. Lots of tactical options there. Just remember, this is a BRIGHT light, and you can see the beam in the night air, leading right back to the source. 

Tracers work both ways.

That said, the all aluminium body, with its anodised finish, o-ring seals and nitrogen charged lens cavity make for a pretty solid piece. One thing I noted were some imperfections. There is dust on the inside of the objective lens, and when dialed to wide-beam, there is a distinct "gibbous moon" effect where the lens is not quite right. This may be because this is a "replica" rather than a stringently QC'd piece.


Here are a couple of shots of me testing it indoors, from room-sweeping, to tight spot. In its room-sweeping end (or any of the wide angles, it also casts a secondary diameter, giving you a pretty good field of illumination at the "up close" distances, great for trails and sweeps.

I also took it out to the valley near Puffing Billy scenic railway, and had a bit of a play with it.


This is a really cool light, and I really enjoy taking it out and beaming it around. It is very powerful though, and I am always careful to steer clear of aircraft, delicate eyeballs and Sith Lords.

Tuesday, June 4, 2013

Review: Civilian Labs - Hazard4 - Loader RG Harness

Ages ago I covered an essential piece of my EDC, my custom made EDC holster harness. This faithful piece has been with me for years, and has reached the end of its life. I had contacted Darrin Talbott of Extreme Gear Labs to commission him to build me something, but alas, he's just far too busy to make a wacky one-off custom job for a blogger.

Check out his Facebook to see the cool Operator gear he makes. That news sent me looking for an alternative.

I was lucky enough to spy the Jerking The Trigger post on the Hazard4 Poncho and following the links, saw that Hazard4 offered a modular holster rig! Tay from HorNest did me a solid, and shipped some over.

Hazard4 are the "Tactical" arm of Civilian Lab makers of fine modular kit. The link I followed brought me to these, this is the Loader rig
with the optional extra anatomic harness.

What it is is two sets of the Escape Rig, one for each side. The two halves are identical, so I'll cover them as just the single unit.



Here are the two Escape halves, with the Anatomic shoulder harness, and another piece at the bottom to hold them together for stability.

The pouches are made of Dobby Nylon and have "PU X 2" treatment, and measure 12.5 x18 x4 cm
(~5" x7" x1.5") externally. The main panel is faced with two hook and loop closing pockets, one that fits my Surefire 6PX like a glove, and the other which his more squat. Both of these pockets are elastic sided, and open cornered. Bear this in mind when looking to fill them.

In this shot you can see some of the rotating buckles  that are fitted to each corner, each backed with a tab of the same padded material that backs the pouch for wearer comfort.  This is some very thoughtful and innovative design. no more buckle-pinch!

You can also see one of the tri-glide buckles that sit on the middle of each of the four sides. These are for accessory loop and strapping, and I'll get into that a bit later.

The 2013 version of this pouch has all black labeling and non-reflective zippers and fittings, for even lower profile wear.



The "back pocket" of the pouch is an open slot, wide enough for my receipt and card filled wallet, and is mesh-sided to cut weight and improve breathability and drainage. (Luckily Australian money is plastic, in case I ever take a dunk...) You can see another of those elastic-looped tri-glides here, to which I have dummy-corded my wallet. No more dropping it into the toilet, off piers, or leaving it on cafe counters for me!

My iPhone sits in the corresponding other side.

What you cant see is the wide swathe of black loop field, for affixing a hook-backed holster, like the Stick-Up.

You can also see the double zipper here of the inner pocket. Very useful!

Inside that inner pocket, you see where some real thought has gone into making these pouches. As well as the tough nylon outer, they are lined with quilted micro-suede

They also feature a series of webbing and elastic channels to fit your tools and needful gear, I have my SAR Dead Ringer comb and CRKT K.I.S.S. folder in mine on this side. Passports, and paperwork on the other side.

The pocket opens all the way to the bottom, but, like a good admin pouch, it has webbing retainers, keeping it from flopping flat, but catching it at about 45o so your pens, USB sticks, or whatever don't tumble off into the wide blue yonder.

The back pocket has a press stud on webbing closure, with two sizing options, which is great. I tend to clip my wallet in with the big, and my phone in with the snugger length.



The back of the pouch features a belt loop,wide enough for all the belt I tried it on ( both my 5-11 TDU belts, the 215Gear Ultimate Riggers belt, and the PM Leather Hobble Belt.

It also features a press-stud flap option, for quick-release needs.

Why even have a belt loop? Modularity!

 Those corner buckles attach to the included cross-straps, which are two fully adjustable nylon webbing straps, with a press-stud in the middle, to connect the two.

One of the coolest things about this whole system is that it can be worn so many ways.

All of the straps will "double-back" through the buckles for a really secure fit.and the tri-glide attachment points allow you to rig any number of stability or alternative attachment options. The rotating corner clasps mean that the straps stay flat no matter what configuration you wear them in, and they stay upright as you move, depending on how you wear it.

The included cross-straps are a little more versatile than the Anatomic straps, but not nearly as comfortable. The pouches can be worn under the arms, holster style, singly or in pairs, horizontally or vertically, but also on the hips on a sling, as a backpack, slung cross-ways like a bandoleer, on the thigh as a drop-leg or on the front of the chest or even as a shoulder bag.

I used one of the cross-straps to act as a kidney-height stabiliser,  having found that on their own, the pouches slid forwards when i bent over without them.
 Here's the package insert, showing some of the carry options.....


One last thing. Each of the pouches comes with a "Shuttle Pouch" which is made from the same Dobby Nylon, and lined again in the quilted micro-suede with mesh pockets along with nylon strapping. The Shuttle pouch is designed to fit into the "Back pocket" of the main pouch,and be clipped in. It features waterproof zippers and a set of webbing eyelets on each of the four back corners for dummy-cording (mmm, dummy-cord: looks silly, keeps your gear on you...)


This was a seriously feature and function filled set of kit.

I've been wearing it now for a few weeks, getting the configuration and fit right and I must say, it has been one of my better EDC investments for some time.  I wear it every day, almost all day in some cases.

I don't feel "dressed" with out it, and it really is my go-to item when it's time to run out the door; be it emergency, fire, flood or groceries.

Saturday, June 1, 2013

Events: SSAA SHOT Expo 2013


I went along to my very first SSAA SHOT Expo last weekend and had a great time.

I've watched with envy as the American SHOT Expo's have been reported in the past and it was great to find out there was one in my own city of Melbourne.

Having missed out on the Land Warfare Conference last year I made sure that I would make it to this one.

I wasn't disappointed! Here's me plugging some pixelated piggies at the Australian Deer Association booth.

I met up with a friend of mine who has been working in private security, and we had a good wander around. The crowds were quite something, even for a Sunday afternoon, but I got to see it all. It was great to finally meet Ben Doyle Cox from Platatac as well

 I was able to make some great new contacts, like the fine folks at Alpine Country, distributors for Stony Creek who took a bunch of time out of their day to go through their whole range with me. I look forwards to seeing some more of their stuff soon, and perhaps giving it a go in the field.



McMillan Rifles had the big guns ... .338 Lapua, .50 cal, and all manner of reach out and touch someone shiny.
I had a good long chat with Joh Dahlgren, of  Dahlgren Trading, importers of Swedish hand made knives, axes and  wrecking bars.

These were some very nice pieces; handcrafted from Swedish steels and some very nice handles in American hickory.

I especially liked the four archeological replica style viking era axes.





























There were all kinds of fun things in cabinets, and on the walls for us to check out like this Colt .22LR

I was surprised to see so many pistols, considering the Victorian pistol laws, but it was great to see them up close.









We also saw a whole bunch of taxidermy...
















A whole bunch of rifles and scopes at the Gun Emporium, a veritable smorgasbord of shooters.
The Outdoor Sporting Agencies stand had a wide range of longarms fro ma variety of vendors.

Lightforce had a great range of on-scope lighting as well as vehicle mounting lights.


The Beretta stand had partnered with Pelican cases, as well as showing off their own large range of irons.













Probably my favourite pieces of hardware were these two bulpup conversions at the Frontier Arms stand.

I really liked these, and were I in the market for a longarm, I would probably look strongly at these.








They also had a cabinet of target pistols seemed a lot more in keeping, and they are gorgeous pieces of precision machinery.




























 I enjoyed checking out the Moroka.30 Stand, especially their Snakebuster Gaiters and meat carrier packs.












I had a great time catching up with the guys at LEGear, especially Josh, for whom I've done some reviews (1 , 2 , 3 , 4 ) in the past. 

I also met the visiting CEO and Vice-President from FENIX who were there with LEGear. Look out for some more from them soon!
Lastly, I dropped in on 5.11 Tactical, and caught up with them too, chatting with Bill over from the US. I had a great time, and got the low down 
on a variety of their products, and scored a set of their Stryke tactical pants, stay tuned for a review soon.








All in all it was a great show, and next time I will have a real agenda, and a plan to cover it all a lot more systematically.


Wednesday, May 29, 2013

Review: Benchmade - Figure 5 cutter

A while ago, as I was packing up my kit to go and do the IRL Shooter: Patient Zero lasertag event, I seem to have mislaid my Gerber Strap cutter, which made me a bit sad, because I do very much enjoy having a safely cutter on hand, for a variety of adventurous reasons. 

Combat shears are all good and well, and I certainly keep them on-hand when I am out and about doing adventure things, as part of my response kit, but there are occasions where you just want to pull-place-cut your way out of a problem.


When LEGear.com.au put on a big sale, I was quick to snap up a variety of goodies, and this, the Benchmade 5 Safety Cutter Hook was one of them.

I have been carrying this one in my pocket along side my CRKT Eat'n'Tool since it arrived, and the two marry very nicely. The Delrin Snap-Fithard sheath offers a friction release carry option, and itself has a variety of features. 

With three webbing loopholes, as well as two lanyard or Tek-Lok capable holes, you can lash, loop or bolt it to pretty much anywhere. It will also take the MALICE clips from Tactical Tailor.
The deep crenelations on the spine give a really solid grip without tearing at the hand, thanks to their rounded shape, similarly, the "inside edge" where the middle finger rests, with its correspondingly smaller crenelations adds to that grip.

The main finger hole is 2.85cm (1.12") in diameter, making it a good fit, even for a gloved hand. The "mouth" of the blade section is 12.7mm (0.5") so can accommodate a wide variety of materials, and layers. 

 I will be mounting this one to my Zulu Nylon Gear CAOS Admin Pouch which in turn rides on my Bullock Echo daypack when its not in my pocket.
The safety hook aspect of it means that it is great for cutting cords, strapping and opening packaging, but as a rescue tool, there is something very reassuring about being able to go in fast hand hard to get someone out of a bind without worrying about gutting them.

The two extra holes are something of a mystery to me. They are not oxy-tank wrenches, (which are oblong), and they are in fact joined by a thin gap, that runs from the middle of the bottom, through the finger hole, and int othe second eyelet. I can only imagine these are cutting slots, and weight saving holes. Does anyone know what purpose they serve?

I cut a few things to test it out, some 1" webbing, a zip-tie and some paracord. Fast, efficient, and fit for purpose. Benchmade claim that even after 500+ cuts, the initial pull-to-cut strength is 4 times less that that of their competitors (1.8 kg or 4lbs) and will even cut 5 layers of webbing. That's a lot. I look forwards to using this more, but not NEEDING to use it, if you follow ...





Sunday, May 26, 2013

Review: Benchmade - SOCP CQB dagger


So, in my recent delivery from Tay at HorNest Singapore, I finally laid my paws on this piece that I first saw on 2Cent Tactical (or at least, the Spartan Arms CQB version) but primarily from the Soldier Systems write up of this one specifically, the Benchmade SOCP Close Quarter Battle dagger.   


Being a dagger, this is a restricted item in Victoria, where I live, but I hold an exemption of the Weapons Control Act as a bona fide collector.

I had held one in the past, when in the Platatac retail shop. Now I have one.
 This is a piece of delicate, singing steel. This is no kitchen knife. No camp knife for chopping branches and making kindling.  This is for putting the pain into people.

Both the dagger and the red skeletonized trainer blade are made of 440C blade steel. The dagger weighs 62.37g (2.20oz ) and the trainer 65.49g (2.31oz), with overall lengths of 18.42cm (7.25") and 17.30cm (6.81") and blade lengths of 8.18cm (3.22") and 7.06cm (2.78") respectively.


Worth noting that on the dagger, the actual sharp edge only accounts for a little over a third of that length but comes to a wickedly sharp point.

10ga phlebotomy needle sharp.

The tail end features a large ring, with crenelations cut into its cap for a very positive grip and the narrow spine is shaped to fit a tight grip, with further crenelations cut into the middle "knuckle gap"for added gripping power.



The trainer and the dagger have the exact same layout, and this makes a very nice and safe transition, over more traditional "training" blades. The safety-red trainer looks, feels and acts almost exactly the same as its more deadly sibling, allowing you to train like you fight, and fight like you train.

Just what is it for then? This blade was designed to be an on-hand backup for a firearm in close quarters fighting.


The narrow spine and ring-grip allows the wielder to maintain a grip on a firearm, be it a pistol or longarm, and have it on-hand to fend off attackers in grappling distance, without switching hands.


One can quite comfortably be carried whilst you are using your hands for other things (just TRY to take my lemonade away).

The idea behind this blade is that it is not a "fighting knife", but a "last-ditch" weapon to buy yourself time in a very dire situation. It is light, fast and very very good at putting holes in things that need ventilating in a "never touch me again" situation.

Being able to hold a knife and still hang operate another tool, or object simply gives you a time advantage over someone who needs to drop an item and draw a knife.

Part of the key to this is the design of the ring grip and how the sheath works. The injection molded sheath with retention clip and lanyard holes fits neatly into a MOLLE channel, taking up three rows, and is held snugly in place by the clip and the flared end of the sheath.

The placement of the lip pf the sheath and the ring means that you can hook the tip of a finger through it, yank it up and out and into a usable grip from just slapping your palm against it, and making a fist whilst drawing back. Its an unusual maneuver, and I am particularly glad that I got the trainer, because I can see myself giving my gear or self an impromptu shave practicing this.

The sheath is available in olive drab or black, and it really does blend in, as well as only adding 28.35g (1oz) to your load. This is a stealth piece if i ever saw one.

A beautiful, functional, dangerously stealthy piece. I really like it, and am very pleased to have added it to my collection, and in the event of the breakdown in society, I'll be very happy to have it in my arsenal.





Wednesday, May 22, 2013

Review: WTF - Ti wrench and pry tool

More Kickstarter goodness.

I managed to snag a "second" as an early trial piece for the WTF mini titanium keychain Kickstarter, from Brad, creator of the Bottle Grenade "the-last-opener-you-will-ever-need"

I am always on the lookout for little tools liek this, because I really like having them on hand, in my pack, in my EDC, without being totally overburdened (don't laugh).

This one was a "second" as it was slightly mis-aligned, you can see that the internal cutouts are not quite centered, leading to a slight reduction in strength, so when they were offered for immediate discount sale, i snapped one up.

The Kickstarter project offered these in three materials and I pull directly from the Kickstarter brief for these:

Aluminum 6061-T6 - Ultimate Tensile Strength is 45,000 psi and an elasticity modulus of 10,000 ksi (Soft) ~4.4 grams


Titanium Ti-6Al-4V - Ultimate Tensile Strength is 138,000 psi and an elasticity modulus of 16,500 ksi (Springy) ~7.8 grams

and finally a Parkerized Chromoly 4130 - Ultimate Tensile Strength - 97,200 psi but has an elasticity modulus of 29,700 ksi (Stiff) ~11.5 grams (and a Rockwell hardness of B 90–96 holy crap!!)

I opted for a Ti and a Chromoly, but they aren't expected till November (6 months away, I might DIE) so was thrilled to get this little guy in my hands.

Brad even zipped it though his anodizing mix, and I got to select my colour, this is the 55VDC anodizing and it gave a lovely pale gold colour to the tool.

So, what does it do?

The dimples on the sides correspond to 1/4"  on one side, and 1cm on the other.

The middle cutout features the following sockets:
Standard: 1/4", 5/16", 3/8", 7/16", 1/2"
Metric: 6mm, 8mm, 10mm, 11mm, 13mm


I actually struggled a little while to find some bolts to test this on. Then I realised that half of my house is covered in Ikea GORM shelves   and I set to tightening those suckers up. The teeth of the wrench slipped neatly into place, and away I went. This is indeed a Wrench That Fits.

The next aspect to test was pretty easy to do. The texturesd bevel of the pry-bar end made quick work of jars, cans and a variety of "things to pry" that I might have at one time or other thought to use a screw-driver, butter knife on, but NEVER the end of my multi-tool knife blade (oh no, that was snapped off by rabid goblins).

The "outside edges" are all smoothed off, giving a very comfortable grip, all the way down to the pry-bar end, which is not rounded, but smooth. Certainly enough grip to be used as an impromptu kubaton, if the need arose.

The internal edges are crisp, but not rough, and given that this is a titanium tool, I expect they will probably pretty much stay that way. 

Along with my SAR GlobalTool Dead Ringer comb, and my Snowpeak Spork this is the third titanium tool that I have added to my EDC, and I am really pleased with it so far.

Comparing it with my CountyComm Micro Widgy pry bar, it is a little shorter, and given its complement of ten socket options as well as a pry end, is significantly more multifunctional.

That said, I'm not throwing out my Micro Widgy either. Two is One, One is none.

So as not to keep all my eggs in one basket, (and really, two pry bars on one set of keychain tools is a bit excessive, even for me) I have taken to wearing the WTF on my necklace, with a simple split ring through the lanyard hole, where it sits beside my SAR Global Tool MoonGlow and my 500-700BCE pre-Han dynasty Chinese bronze arrowhead that I got whilst visiting my parents in Beijing. The irony of 2500 years between these two pieces is only magnified by the delightful chiming they make as I wear them, especially when being vigorous, or adventuring.

Friday, May 17, 2013

Review: Blackhawk - Removable side plate carriers


If you've been a long time reader, you'll know a few things about me: I'm in Australia, I'm not MIL or LEO, but I have a keen interest in modular, rough and tough gear that I can make use of, and am more than happy to take existing purpose-made kit and modify its usage to fit my own particular need and resources.

I'm fond of armour, having been a practitioner of kendo for 16 years, and LARP type silliness, as well as a variety of adventurous pastimes that might involve a reasonable amount of blunt force other trauma. I've covered both helmets and plate carriers before (like the Platatac MAC, Strike Industries SPC and others). I've also cover lots of pouches, big and small, so when a chance to acquire some modular plate carrier pouches came up, I jumped on it.

More armour, more places, more pouches? yes please.

This is the Blackhawk Removable Side Plate Carrier It comes in pairs, and is designed to fit the Blackhawk 6” X 8” Level IV plate which is a formidable piece of armour that is outside my scope or means, but goes hand in hand with this piece.

So, what is it, and why is it so cool?

Constructed from 500D Cordura, this light but tough pouch is sewn on three sides, with a hook-and-loop mouth at the top, featuring two webbing loops at the lip, to give you purchase to open it smoothly.

On the face and back, PALS/MOLLE webbing runs in a 4x4 grid on one side, and a 3x4 grid on the other, such that the webbing on one side complements the other, rather than mirroring it.

This give you two different fits, depending on how you want to attach it to whatever you are mounting it to.

The concept of these is to give the wearer a pocket to carry a plate, on a vest or rig that otherwise doesn't have that option, wither a Front/Back configuration or a cummerbund that's just "all PALS/MOLLE and no plate pocket". The MAC cummerbund I have does have those pockets included, which as I've covered before, I have filled with polyethylene cutting boards both for space filling bulk, rigidity and also or the blunt-force trauma and stabbing and cutting protection it offers.

Sure its not ballistic protection,  but to be honest, the chances of me needing that level of protection are very slim given my situation, AND its not legal for me to acquire here anyway.

I took one of those boards out and fitted it into one of the carriers, and closed it up. Instant extra armour panel, brilliant. I fitted it first to the cummerbund, and this was where the complementarity webbing came in handy. I could choose to have it ride a little high, or a little low, just by flipping it.

Modular, light and configurable. Nice.

The "removable" part comes to bear as a result of the attachment method. The panels each came supplied with three of the Blackhawk 7 width Speed-Clips which slip in and out of the pouch to the substrate and then clip in to the top and bottom layer.

One thing I noted was that the PALS/MOLLE channels were standard 1" i n the middle two channels, but 1.5" or so at the edges, which when combined, gives you a -5- channel reach, as needed. Again, good for configuring your rig to best fit need and comfort.



Another aspect of this is that you can layer these panels over the top of regular plate carriers, and put an extra layer of armour between you and harms way, in modular fashion, without loosing PALS/MOLLE real-estate.

Here you can see I've put the pouch on the front of my MAC. No reason though that you couldn't put this on a pack, a thigh-rig or anywhere else with 3 rows of MOLLE webbing.

One of the "alternate" uses I thought of was as a admin pocket, for paperwork or other flat items, perhaps a Kindle sized tablet (it doesn't fit my iPad 1), as a thin dump-pouch, or even as a boot to catch a large slung item, like my axe or even perhaps, my Deuce.

All in all, this a pretty neat accessory, even when its primary purpose isn't applicable, having a rugged, seal-able and modular pocket is ALWAYS a good addition to your load-out.





Related Posts Plugin for WordPress, Blogger...