Ask me anything!

 As I find myself a little shy of new
gear to review currently, I thought I might put the question out to you my readers to see if there was a topic you'd like my thoughts on? is there a type of gear you'd like me to try out? Is there a situation you'd like my contingencies for? Is there a skill or set of skills you'd like to hear more about and test me on? Piece of kit you'd like me to do a YouTube on?

Lay it on me in the comments or DM's and i'll do my best to answer in upcoming posts!

Review: EDC Monster Titanium Multi-function Pry Bar

Time for another pry bar! Having just covered the small titanium pry bar I wear in a belt pouch you might be asking why i have yet another one. (on top of the WTF prybar I wear around my neck as EDC). The short answer is Two is one, One is none, and I have two hands and hate being kept out of places. 

This is the EDC Monster Pry-Bar, which was launched via a Kickstarter project. As their sixth successful project ( they make a lot of folding pen-knifes and the like). The thing that caught my eye about this tool however was  its multi-function design. It's packed full of options whilst retaining rugged construction.

Milled from a block of corrosion resistant Gr5 Titanium, the tool features a number of useful features the designers workshopped from common EDC tools.  

First and foremost the pry-bar end of the tool is dual-beveled on the top face and has a bevel on the under side too, finishing up as a 1-2mm flat edge 15mm long rather than a sharp chisel edge. Not sharp by any stretch but plenty pointy enough to cut taped boxes and packages open. 

A good sized bottle opener sits at the belly of the pry end, in front of a finger notch. The double sided beveling allows the tool to be worked-into a gap easier than if it were flat on the underside, which is handy.

 The back spine side of the tool features a swiveling, magnetised cover that turns to reveal two hex bits, a S2 Alloy Steel  Phillip's head and a flat head driver, both held in place with magnets, but easily popped out. both drivers fit the ratcheting driver ring seated in the butt-end of the tool, it ratchets in one direction only, so you flip the tool to change direction of driving.

It's worth noting that the driver bits don't lock into the ratchet driver, and need to be held in place by the user, (placing a thumb on it seemed to work fine, but worth noting) . You could swap out the drivers with others as long as they fit in the recess.

Recessed on the underside of the tool is a magnetically affixed, titanium bodied "everlasting graphite" nibbed pencil. More than just a gimmick, these pencils are very useful for always to hand writing implements, though I have found the nibs to be fragile on occasion, they do write really well and are super handy. Astute readers may have noticed one lanyareded to my other EDC pry-bar

The pencil is short (1.65")  but not unworkable so its a very useful addition and is securely held in its recess, protecting the sometimes brittle nib, when not in use. 

The very butt-end of the tool features a tungsten carbide spike to allow glass breaking and inscribing into hard surfaces. It also features a lanyard hole for fitting you favourite beads or "don't-loose-me" cords. 

As well as the well placed groves milled in for grip, there are four recessed slots (2 on front, and 2 on the back) for fitting tritium vials. But due to shipping restrictions, they were not able to provide the tritium vial, but they did will provide luminous rods as add-on options. I have yet to install these but should be a matter of applyng a dry-clear epoxy glue. The tool has a removable belt clip, but also comes with a snug kydex sheath with a belt clip. All told the tool including its bits and pencil weighs only 85g (3oz) and measures 14.2cm (5.6") x 2cm (0.82") broad. Its a nice compact tool packing a lot of utility into its small frame.